Owner’s Manual
Important Safety Instructions
Warranty Information
Installation
Fax/Modem Protection
Indicator Lights
Copyright © 2010 Tripp Lite. All rights reserved.
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Voltage Regulator
Model: VRX2008R (220V, 50/60Hz Input, Output)
•
Install your voltage regulator indoors, away from excess
moisture and heat, direct sunlight, and dust and other conductive
contaminants.
•
For best performance, keep the indoor temperature between 0º C and
40º C (between 32º F and 104º F ).
•
Leave adequate space around all sides of the voltage regulator for
proper ventilation.
•
Connect your voltage regulator directly to a three-wire, grounded
AC power outlet. Do not remove or modify the ground pin of the
voltage regulator’s plug. Do not use adapters that would eliminate
the voltage regulator’s connection to ground.
•
Do not use extension cords between the voltage regulator and the
AC outlet. If necessary, a Tripp Lite Surge Suppressor may be used
between the voltage regulator and the AC outlet.
•
Use of this equipment in life support applications where failure
of this equipment can reasonably be expected to cause the failure
of the life support equipment or to significantly affect its safety or
effectiveness is not recommended. Do not use this equipment in
the presence of a flammable anesthetic mixture with air, oxygen or
nitrous oxide.
TRIPP LITE warrants its products to be free from defects in materials and workmanship
for a period of two years from the date of initial purchase. TRIPP LITE’s obligation under
this warranty is limited to repairing or replacing (at its sole option) any such defective
products. This warranty does not apply to equipment which has been damaged by accident,
negligence or misapplication or has been altered or modified in any way. This warranty
applies only to the original purchaser who must have properly registered the product within
10 days of purchase.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of
implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to
the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE is not liable for any costs,
such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software,
loss of data, costs of substitutes, claims by third parties, or otherwise.
Regulatory Compliance Identification Numbers
For the purpose of regulatory compliance certifications and identification, your Tripp Lite
product has been assigned a unique series number. The series number can be found on the
product nameplate label, along with all required approval markings and information. When
requesting compliance information for this product, always refer to the series number.
The series number should not be confused with the marking name or model number of the
product.
WEEE Compliance Information for Tripp Lite Customers and Recyclers (European
Union)
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing
regulations, when customers buy new electrical and electronic equipment from Tripp Lite
they are entitled to:
• Send old equipment for recycling on a one-for-one, like-for-like basis (this varies
depending on the country)
• Send the new equipment back for recycling when this ultimately becomes waste
Tripp Lite follows a policy of continuous improvement. Product specifications are subject to
change without notice.
1
Connect your voltage regulator to an electrical outlet.
2
Plug your computer and electronics into your voltage regulator’s
outlets.
NOTE: Four outlets feature Automatic Voltage
Regulation (AVR) only and four outlets feature surge
suppression only. Connect your computer and electronics
accordingly.
3
Turn your voltage regulator’s power switch on.
NOTE: This connection is optional.
Your voltage regulator will
work properly without this connection.
Using telephone cords,
connect your wall jack to the voltage regulator jack marked “IN” and
your equipment to the voltage regulator jack marked “OUT”.
BOOST:
This yellow light will turn ON whenever your voltage
regulator is boosting low AC line voltage up to nominal
voltage levels.
POWER:
This green light will turn ON when your voltage regulator is
receiving normal AC line voltage. It will blink if the system
load is too high at very low voltages. Reducing loads at very
low voltage levels will provide optimal AVR operation.
CUT:
This red light will turn ON whenever your voltage regulator
is reducing high AC line voltage down to nominal voltage
levels.
201006066 • 933028-EN
