manualshive.com logo in svg

Tripp Lite NGI-S08C2POE8, Owner'S Manual

Share
Download
Tripp Lite NGI-S08C2POE8 Owner'S Manual Download Page 19

 

19 

 

1000

 

Illuminated  Link speed at 1000Mbps 

Off 

Link speed at 10/100Mbps 

LNK/ACT   

Illuminated  Ethernet link-up 

Blinking 

Activity (receiving or transmitting data) 

Off 

Port disconnected or link failed 

 

3.4.

 

DIP Switches 

 

1.

 

PWR – Primary power input from terminal block. 

ON  Primary power alarm reporting is enabled. 

OFF  Primary power alarm reporting is disabled. 

 

2.

 

RPS – Redundant power input from terminal block. 

ON  Redundant power alarm reporting is enabled. 

OFF  Redundant power alarm reporting is disabled. 

 

3.

 

STORM – To enable/disable storm control with default rate setting. 

ON  Broadcast/DLF storm control rate is 300pps. 

OFF  Broadcast/DLF storm is controlled through software. 

 

4.

 

QoS – To enable/disable port priority (on P1 & P2). 

ON  QoS on P1 & P2 is enabled. Port 1’s & Port 2’s priority=4. Other ports priority 

is 0. 

OFF  QoS is controlled through software. 

Alarm Relay

 

Summary of Contents for NGI-S08C2POE8






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands