manualshive.com logo in svg

Tripp Lite NGI-S08C2POE8, Owner'S Manual

Share
Download
Tripp Lite NGI-S08C2POE8 Owner'S Manual Download Page 18

 

18 

 

 

3.3.

 

LED Indicators 

This Switch is equipped with Unit LEDs to enable you to determine the status of the Switch, as 

well as Port LEDs to display what is happening in all your connections. They are as follows: 

 

System LEDs 

PWR

 

Illuminated  Primary Power on 

Off 

Primary Power off or failure 

RPS 

 

Illuminated  Redundant (secondary) Power on 

Off 

Redundant Power off or failure 

ALM

 

Illuminated 

Alarm for following conditions (when DIP 

switches are turned on) 

 

Primary Power lost 

 

Secondary power lost 

 

If storm control exceeds the threshold 

 

If port 9,10 are link down 

Off 

Normal operation   

Interface LED 

SFP (port 9-10) 

Illuminated  Ethernet link-up 

Blinking 

Activity (receiving or transmitting data) 

Off 

Port disconnected or link failed 

PoE (1-8 Copper Port) 

Illuminated  Supplying power to PD 

Off 

No any power supply to PD 

Port Number 1-8 Copper port LED (1000Mbps) 

Alarm Relay

 

Summary of Contents for NGI-S08C2POE8






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands