Tripp Lite NGI-M08C4-L2 Owner'S Manual Download Page 44

Page: 44 / 313

UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500

Metric:1 ASYMMTU:0

RX packets:17931 errors:0 dropped:6680 overruns:0 frame:0

TX packets:6500 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:500

RX bytes:3565872 (3.4 Mb) TX bytes:1173040 (1.1 Mb)

5.1.4.2.

Web Configuration

Parameter

Description

Management Host Settings

Management Host This field configures the management host.

Subnet Mask

This field configures the subnet, so that any host in that subnet can

control the switch

Apply

Click

Apply

to take effect the settings.

Refresh

Click

Refresh

to begin configuring this screen afresh.

Management Host List

No.

This field displays a sequential number for each management host.

Management Host

(IP/Mask)

This field displays the management host and the number of mask

bit.

Action

Click

Delete

to remove the specified entry.

Summary of Contents for NGI-M08C4-L2


























































































































































































































































































































Search results

Summary of Contents for NGI-M08C4-L2

Reviews:

Related manuals for NGI-M08C4-L2

Brands by name

Popular brands

Tripp Lite NGI-M08C4-L2, Owner'S Manual

Search results

Summary of Contents for NGI-M08C4-L2

Reviews:

Related manuals for NGI-M08C4-L2

Brands by name

Popular brands