Tripp Lite NGI-M08C4-L2 Owner'S Manual Download Page 305

Page: 305 / 313

305

9.8.3

ONVIF

9.8.3.1

CLI Configurations

Node

Command

Description

enable

show onvif

This command displays the ONVIF configurations.

enable

configure terminal

This command changes the node to configure node.

config

onvif enable

This command enables the ONVIF on the Switch.

config

onvif tx-interval

<6-3600>

This command configures the tx interval for the

ONVIF.

config

no onvif enable

This command disables the ONVIF on the Switch.

config

no onvif tx-interval

This command reset the tx interval to default for the

ONVIF.(Default: 6 seconds).

9.8.3.2

Web Configurations

Parameter

Description

ONVIF Settings

State

Select option to enable / disable the ONVIF feature on the

Switch.

Tx Interval

Configures the sending ONVIF discovery packet interval.
Valid range is 6 ~ 3600 seconds.

Apply

Click

Apply

to take effect the settings.

Refresh

Click

Refresh

to begin configuring this screen afresh.

ONVIF Neighbor Information

Port

The connected port of the ONVIF device.

IP Address

The IP address of the ONVIF device.

Summary of Contents for NGI-M08C4-L2


























































































































































































































































































































Search results

Summary of Contents for NGI-M08C4-L2

Reviews:

Related manuals for NGI-M08C4-L2

Brands by name

Popular brands

Tripp Lite NGI-M08C4-L2, Owner'S Manual

Search results

Summary of Contents for NGI-M08C4-L2

Reviews:

Related manuals for NGI-M08C4-L2

Brands by name

Popular brands