Triotech Storm VR Owner'S Manual Download Page 6

Page: 6 / 72

Storm-OM-001 -

Storm-OM-001

28 February 2020

This document, including the information contained herein, is proprietary to Triotech Amusement Inc.

Introduction

This manual will provide you with the necessary instructions on how to operate and
perform maintenance on your Storm attraction.

IMPORTANT: SAVE THESE INSTRUCTIONS.

Copyright law and industrial property law protect the contents of the Storm, its
components, its software and its design.

The Storm will be delivered to your location and will include all necessary parts and
components to easily install it.

and Support

Team.

Triotech Amusement Inc.
780 rue Marion
Joliette, Québec
Canada
J6E 8S2

Phone: +1 (450) 760-9082 (Press 1 for Service and Support)
Toll Free (US/CAN): 1-888 465-4634
Fax: +1 (450) 760-9348

[email protected]

24-hour technical support

Summary of Contents for Storm VR









































































Search results

Summary of Contents for Storm VR

Reviews:

Related manuals for Storm VR

Brands by name

Popular brands

Triotech Storm VR, Owner'S Manual

Search results

Summary of Contents for Storm VR

Reviews:

Related manuals for Storm VR

Brands by name

Popular brands