manualshive.com logo in svg

Trilithic Three, User Manual

Share
Download
Trilithic Three User Manual Download Page 32

30

Model Three - Operation Manual

Measurement

Use the 

MEASUREMENTS

 menu screen to set the measurement

parameters of your device.

Use the 

F

2

 and 

F

3

 keys

 

to scroll through the command choices.

Transmission

Use this selection to enable the transmission mode.

Press the 

F

1

F

1

 

(ENTER)

 key, or press the 

__

 and 

 keys to enable

the Transmission mode.  The selected transmission state 

ON

 or 

OFF

is displayed in the window near the bottom of the display screen.  Use
this parameter to test for transmission characteristics and loss of in-
between connections in your CATV system (see 

Chapter 6:

Advanced Operation,

 

Transmission Characteristic Test

).

Level Units

Use this selection to set the signal level units for the Model Three.
The selected signal level units are displayed in the window near the
bottom of the display screen.

Press the 

F

1

F

1

 key or press the 

__

 and 

 keys to switch between

dBmV

, 

dB

μμμμμ

V

, or 

dBmW

.

Summary of Contents for Three









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands