TRIGA TR-FFT Installation & Operation Manual Download Page 18 | Manualshive

Page: 18 / 33

TRIGA TR-FFT Installation & Operation Manual Download Page 18

18

PRELIMINARY: TR-FFT Fire Fighter’s Telephone Manual — LS10309-001TR-E:A 04/28/2021

Installation

TR-STSR/TR-STSS Installation

Figure 3.11 TR-FPJ (Phone Jack) and TR-RHS (Handset)

Figure 3.12 TR-FFT-to-TR-FPJ Wiring Connection

3.9 TR-STSR/TR-STSS Installation

The Single Telephone Stations are packaged in a series of parts. The telephone chassis, backbox, break glass kit and door with

key lock are all ordered separately. Up to ten remote handsets may be operated simultaneously.

3.9.1 Assembly of Units with Coiled Cord Handsets

The following assembly steps are for telephones with coiled cord handsets. These steps must be accomplished once the enclo-
sure has been mounted and the system wiring is in place.
1. Attach the System wiring to the terminal strip on the telephone chassis assembly.
2. Insert the 6-32 nut in the backbox. Do not tighten the nuts.
3. Install the telephone chassis assembly in the backbox.
4. Install the trim ring on the backbox using the 6-32 wing nuts. Do not tighten.
5. Install the door assembly. To secure, tighten the wing nuts.

To TR-FFT to SLC Terminal TB4
Connectors or other TR-MINIMON

4.7KW, 1/2 watt ELR
(Install on the last device for
Class B telephone circuit only).

TR-FFT

TR-FPJ

«
...
16
17
18
19
20
...
»

Summary of Contents for TR-FFT


































Reviews:

No comments