Tridonic LuxControl DALI XC Manual Download | Manualshive

Page: 4 / 29

background image

How to use this manual

DALI XC_IB 3.0 | 01.2014 | en

4

1

How to use this manual

We are pleased that you have chosen this Tridonic GmbH & Co KG product. So that you can get the most from this
manual, the following information will be set out in this section:

Characters and symbols in this manual

Further information

i

Note

These commissioning instructions describe how to use the DALI XC in the

comfortDIM

system.

Characters and symbols in this manual

The following characters and symbols are used in this manual:

Character/
symbol

Description

1.

Individual steps in the instructions are numbered.

Single-step instructions are indicated by at the beginning of the line.

After a step has been described, a description of the expected results will follow. These results are indicated
by at the beginning of the line.

—

Requirements which need to be checked before carrying out a step are indicated by —.

i

Notes can be recognised by

i

. In addition, notes are identified by the word

Note

.

Table 1: Characters and symbols in this manual

Further information

More information on installing the DALI XC can be found in the installation instructions supplied with the device.

General information on our products can be found on our website:

www.tridonic.com

«
...
2
3
4
5
6
...
»

Summary of Contents for LuxControl DALI XC






























Reviews:

No comments

Related manuals for LuxControl DALI XC

Brand: ABB Pages: 30

Brand: ABB Pages: 15

Brand: ABB Pages: 10

Brand: ABB Pages: 44

Brand: Samson Pages: 48

Brand: Mako Networks Pages: 15

Brand: Eaton Pages: 2

Brand: Eaton Pages: 2

Brand: Eaton Pages: 8

Brand: Febco Pages: 12

Brand: GameSir Pages: 8

Brand: Game ready Pages: 21

Brand: VAMP Pages: 304

Brand: Tactical Pages: 8

Brand: RADEMACHER Pages: 48

Brand: DigiPower Pages: 27

Brand: Gardigo Pages: 6

Brand: VAT Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands