Tridonic LuxControl DALI XC Manual Download

Page: 27 / 29

System extension

DALI XC_IB 3.0 | 01.2014 | en

9.3

Adding or changing DALI XC devices

1. Disconnect the voltage supply to the lighting system.

2. To change a DALI XC device, proceed as follows: Remove the old DALI XC.

3. Install the new DALI XC in accordance with the accompanying installation instructions.

4. Set the

Mode

and

Config

rotary selector switch positions to match the old DALI XC or as desired.

5. Reconnect the voltage supply.

6. Start system extension.

Luminaire assignment to groups is saved in the new DALI XC device.

1 beep sounds.

Luminaire brightens.

7. Finish system extension.

Testing settings

Note

Section

Changing intensity

describes how to change the intensity.

Go to Section "Changing intensity"...

Section

Changing colour temperature

describes how to change the colour temperature.

Go to Section "Changing colour temperature"...

Section

Recalling scenes

describes how to recall scenes.

Go to Section "Recalling scenes"...

Change the intensity if the device is in

GC-A

operating mode.

– or –

Change intensity and colour temperature if the device is in

TuWh

operating mode.

– or –

Recall scenes if the device is in

SC-A

operating mode.

Adjusting settings

Note

The user manual for the masterCONFIGURATOR software version 2.10 or higher describes how to
configure the

operating mode.

Reprogram functions if the device is in

operating mode.

Summary of Contents for LuxControl DALI XC






























Search results

Summary of Contents for LuxControl DALI XC

Reviews:

Related manuals for LuxControl DALI XC

Brands by name

Popular brands

Tridonic LuxControl DALI XC, Manual

Search results

Summary of Contents for LuxControl DALI XC

Reviews:

Related manuals for LuxControl DALI XC

Brands by name

Popular brands