Tridonic luxCONTROL DaLI Msensor 5DPI 14 Product Manual Download | Manualshive

Page: 10 / 52

background image

Product manual DALI MSensor 5DPI 14 | 06-2017 | 1.1 | en

Safety instructions

c

6 / 48

2. Safety instructions

The instructions in this section have been compiled to ensure that operators and users of the DALI MSensor
5DPI_14 from Tridonic are able to detect potential risks in good time and take the necessary preventative
measures.
The operator must ensure that all users fully understand these instructions and adhere to them. This device may
only be installed and configured by suitably qualified personnel.

2.1. Intended use

2.1.1. Proper use

Multi-sensor for DALI system. The device may only be used for this intended purpose.

2.1.2. Improper use

Outdoor use. Extensions and modifications to the product.

2.2. Dangers associated with the operation of the system

½

WARNING!

Improper use could result in injury, malfunction or damage to property.
It must be ensured that the operator informs every user of existing hazards.

½

DANGER!

Danger of electrocution
Disconnect the power to the entire lighting system before working on the lighting system!

½

CAUTION!

Risk of damage caused by condensation
Prior to commissioning the system, wait until the control device is at room temperature and completely dry!

½

CAUTION!

Risk of damage caused by humidity
Only use the control device in dry rooms and protect it against humidity!

«
...
8
9
10
11
12
...
»

Summary of Contents for luxCONTROL DaLI Msensor 5DPI 14





















































Reviews:

No comments

Related manuals for luxCONTROL DaLI Msensor 5DPI 14

Brand: Walchem Pages: 10

Brand: S-COM Pages: 400

Brand: Wave Italy Pages: 16

Brand: TA Hydronics Pages: 14

Brand: Parker Pages: 44

Brand: LAS Pages: 6

Brand: Eaton Pages: 8

Brand: ABB Pages: 44

Brand: Omega Pages: 2

Brand: Zmotion Pages: 34

Brand: Jetter Pages: 24

KOOL STRIDE KS-S

Brand: KOOL-STOP Pages: 8

Brand: WAC Pages: 5

SAE 07.2 Series

Brand: AUMA Pages: 116

Brand: zeeltronic Pages: 15

Brand: M-system Pages: 3

Brand: Idesco Pages: 7

Latherm HZR Comfort

Brand: LAMBERTI ELEKTRONIK Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands