TREX TB75 User Manual Download Page 13 | Manualshive

Page: 13 / 21

TREX TB75 User Manual Download Page 13

Electric Vehicle / Boat Winch

E&OE

©2018 Trex

13

Operation

Winches are high-load pulling equipment with exposed cables, rollers etc that can cause

serious injury if not used correctly or without taking proper safety precautions.

It is

extremely important that you read and fully understand the information in this section and all other

safety warnings / recommendations and usage instructions before using the equipment

. • Do not use

the hand crank to assist a powered winch. This will damage the winch, and may cause personal injury. • It is

recommended to keep the vehicle engine running while using the winch to keep the battery charged.

However, use extreme caution when working around a vehicle with its engine running.

1. Place the vehicle hand brake on, and chock the wheels using suitable chocks (not included). It is

recommended to NOT use the transmission "park" function or leave the vehicle in gear when winching.

2. Pull out the cable the required distance using the "out" function. Always leave at least 4 turns of cable on

the drum to prevent the cable completely unreeling.

3. Hook the object using a pull point, tow strap, or chain (all not included). Never wrap the cable around the

object or hook to the object itself. This can damage the object being pulled and kink or fray the cable.

4. When it is safe to do so, use the "in" function to retract the cable and winch the object. To operate the

hand crank, rotate it right (clockwise) retract the cable.

Double Line Configuration

For loads OVER 50% rated load capacity, it is recommended to use a pulley block (may be supplied) and

double line configuration (Figure F). This reduces the load on the winch and the strain on the cable by

approximately 50%. In double line configuration, the speed of winching is also reduced by 50%.

To attach a typical pulley block to the cable and set up the double line:
1. Extend the winch cable sufficiently, then attach the winch hook to a suitable

point on the vehicle, creating a loop.

2. Disassemble the pulley block by removing a side plate (may be attached with

fasteners or R-clips and pins etc).

3. Place the pulley block over the bottom of the loop in the winch cable. Then,

reattach the side plate.

4. Rig-up to the pulley block hook, then winch as normal.

Figure F

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX `

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX TREX

«
...
11
12
13
14
15
...
»

Summary of Contents for TB75






















Reviews:

No comments