Technical Specifications
Part No.
L-DCE30D-CON
L-DCE60D-CON
Output:
DC Voltage
12V
12V
Rated Current
2.5A
5A
Rated Power
30W max.
60W max.
Minimum Load
3W
6W
Input:
Voltage Range
100-277VAC
100-277VAC
Frequency Range
47-63Hz
47-63Hz
Power Factor
0.99@120VAC
0.98@120VAC
(Typ.) @ full load
0.98@277VAC
0.95@277VAC
Efficiency
79%
83%
(Typ.) @ full load
Wiring
Suitable for 18-14 AWG, rated 300V, min. 90°C
Protection:
Short Circuit
Shut down o/p voltage, re-power on to recover after fault
condition is removed
Over Loading
≤
120% shut down o/p
≤
120% Hiccup mode, recovers
voltage, re-power on to automatically after fault
recover
condition is removed
Over Temperature
100°C ± 10°C shut down o/p voltage, automatically
recover after cooling
Working Temperature
-40°C ~ +60°C (see Derating Curve chart above)
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: To reduce the risk of fire, electric shock, or injury to persons:
Read all instructions before installing system.
Before beginning installation, be sure power is turned OFF to the
power supply and light system.
• The 30W Power Supply operates on line voltage 100-277 VAC.
The 60W Power Supply operates on line voltage 100-277 VAC.
Shock Hazard
:
Whenever hardwiring the LED Power Supply to a
120-volt circuit with an AC dimmer, turn off power at the circuit breaker
before installing. Failure to do so may result in serious personal injury
or death.
Warning:
All wiring must be in accordance with national and local
electrical codes, low-voltage Class 2 circuit. The Power Supply is to
be mounted and wired in accordance with Article 450 of the National
Electric Code (NEC). Failure to install the Power Supply and light fixture
in compliance with applicable codes and regulations may cause serious
personal injury, death and/or major property damage.
• The Power Supply must be installed in a well-ventilated area free
from explosive gases and vapors. Do not install in an airtight, boxed-
in structure. The Power Supply is cooled by circulating air and by
mounting the unit flush to a surface to allow for heat transfer. Operate
the Power Supply at cooler surrounding air temperatures to extend
the life of the unit. See Derating Curve for temperatures above 40°C
(104°F).
•
Operate only within the specified ambient temperature range of -40°C
(-40°F) to 60°C (140°F).
Note: It is normal for the LED Power Supply to feel warm when under
a full wattage load.
• The hardwired installation of the Power Supply should only be
performed by a qualified electrician.
• Do not conceal the line voltage input cord or Power Supply inside a
wall, ceiling, soffit, or similar permanent structure, unless consulting
a licensed electrician. This requirement does not apply to the 12VDC
wiring between the Power Supply and the cabinet light system. For
wire runs inside a wall, ceiling, soffit, or similar permanent structure,
use CL2 or better cabling.
•
Do not install low-voltage Class 2 wiring along the same run as AC line
voltage. If the line voltage and low-voltage wires need to cross, keep
them at 90° angles.
• Use only insulated staples or plastic ties to secure ALL loose
wires.
• Route and secure
wires so that they will not be pinched or damaged
when the cabinet is pushed to the wall.
(Continued on page 2)
LED DC Power Supply (30W)
L-DCE30D-CON
24 mm
15/16 in.
178 mm
7 in.
61 mm
2-3/8 in.
Cord
152 mm
6 in.
88 mm
3-7/16 in.
13 mm
1/2 in.
26 mm
1 in.
LED DC Power Supply (60W)
L-DCE60D-CON
54 mm
2-1/8 in.
155 mm
6-1/8 in.
20 mm
13/16 in.
LED Wall Dimmer
LED Power Supply
12VDC, 30W or 60W
Mounting Block
Install Wall Dimmer on
input (line voltage) side
of Power Supply
Line Voltage Input Cord
Neutral (white wire)
Ground (green wire)
Line (black wire)
INPUT
OUTPUT 12VDC
Red
Black
L
Black
N
White
12VDC+
LED DC Power Supply (30W)
L-DCE30D-CON
24 mm
15/16 in.
178 mm
7 in.
61 mm
2-3/8 in.
Cord
102 mm
4 in.
88 mm
3-7/16 in.
13 mm
1/2 in.
26 mm
1 in.
LED DC Power Supply (60W)
L-DCE60D-CON
54 mm
2-1/8 in.
155 mm
6-1/8 in.
20 mm
13/16 in.
LED Wall Dimmer
LED Power Supply
12VDC, 30W or 60W
Mounting Block
Install Wall Dimmer on
input (line voltage) side
of Power Supply
Line Voltage Input Cord
Neutral (white wire)
Ground (green wire)
Line (black wire)
INPUT
OUTPUT 12VDC
Red
Black
L
Black
N
White
12VDC+
Installation Instructions
Hardwire LED Power Supplies
Class 2 • Dimmable 30W & 60W 12VDC Constant Voltage
LED 12VDC Power Supply (30W)
Model: ............ KVF-12030-TDW
Part No: ........... L-DCE30D-CON
LED 12VDC Power Supply (60W)
Model: ............ KVF-12060-TDW
Part No: ........... L-DCE60D-CON
Mounting Block included with each Power Supply.
For best operation, use LED-compatible wall dimmers.
100
80
60
40
20
-40 -20 0 10 20 30 40 50 60 70
Ambient Temperature (°C)
Load (%)
LED DC Power Supply (30W)
L-DCE30D-CON
LED DC Power Supply (60W)
L-DCE60D-CON
Typical Application
Derating Curve
Mounting Block
pre-wired to Power Supply
Page 1
