System Parts:
(1) Dynamic RF LED Remote Control . . . . . . . . . . . . . . . P/N: L-RGBCCT-RMT
(1) Dynamic RF LED Parent Controller . . . . . . . . . . . . . . P/N: L-RGBCCT1-PREC
(1) Dynamic RF LED Child Receiver (optional) . . . . . . . . P/N: L-RGBCCT1-CREC
(1) Power Supply, Class 2, 12VDC 60W max (or) 24VDC 96W max
Tresco
®
low voltage 12VDC or 24VDC LED RGB or CCT light(s) with Starter Cord
Instructions
FREEDiM Dynamic RF Remote Control
For RGB & CCT LEDs • 12VDC 60W & 24VDC 96W
R
3000K
G
3500K
B
5000K
Z1
Z2
RGB CCT Remote Control
L-RGBCCT-RMT
“On” Indicator Light
CCT Slider
for CCT control
(slide with finger touch)
RGB Color Wheel
for RGB control
(rotate with finger touch)
“On/Off” Button
R
G
B
Z1
Z2
3000K
3500K
5000K
Dim Button
Dims up or down
R
G
B
Z1
Z2
3000K
3500K
5000K
R
G
B
Z1
Z2
3000K
3500K
5000K
R
G
B
Z1
Z2
3000K
3500K
5000K
RGB Buttons
Quick preset buttons –
In RGB mode, quickly go to
preset Red, Green or Blue colors
R
G
B
Z1
Z2
3000K
3500K
5000K
R
G
B
Z1
Z2
3000K
3500K
5000K
R
G
B
Z1
Z2
3000K
3500K
5000K
CCT Buttons
Quick preset buttons –
In CCT mode, quickly go to preset
Warm (3000K), Neutral (3500K),
or Cool (5000K) light
R
G
B
Z1
Z2
3000K
3500K
5000K
Switch Mode
Switches unit between RGB and
CCT modes
Home Button
R
G
B
Z1
Z2
3000K
3500K
5000K
Takes any settings back to Start
(Starts over at preset settings, but
does not erase pairing)
Speed-up Button
R
G
B
Z1
Z2
3000K
3500K
5000K
Increases the speed of whatever
RGB program running
Play Button
R
G
B
Z1
Z2
3000K
3500K
5000K
Starts the pre-set programs . Hit play
again stops that program . Hit play
again moves to the next program .
Speed-down Button
R
G
B
Z1
Z2
3000K
3500K
5000K
Decreases the speed of whatever
RGB program running
Zone 1 & Zone 2 Buttons
R
G
B
Z1
Z2
3000K
3500K
5000K
R
G
B
Z1
Z2
3000K
3500K
5000K
Switches between Zones 1 and 2
for independent zone functions
The FREEDiM Remote Control starts out with preset settings:
• RGB preset - all values start at 0-0-0
• CCT preset - begins at 2700K
Remote Control Specifications:
Operating Voltage: . . . . . . . . . . . . . . . . (2) AAA batteries
(included)
Radio Frequency: . . . . . . . . . . . . . 916 .5 MHz
RF Remote Distance: . . . . . . . . . . 66 ft . (20m)
RGB and CCT full-function controls:
The Tresco
®
FREEDiM Remote Control provides color and brightness
controls for RGB or CCT (white color-tunable) lighting on Tresco
®
low
voltage LED RGB and CCT lights . It also controls the intensity (dim
levels) of the lights up to 95% . The digital screen on the FREEDiM
Parent Controller displays the current mode and settings .
The wireless Remote Control must be positioned within 66 ft .
(20m) of Parent Controller and any Child Receivers . Note: outside
interference may affect the signal between Remote Control and
Parent Controller .
(see ‘Signal Interference’ on page 2)
RGB and CCT modes:
Prior to installation you need to select between RGB or CCT LED
lights . Then after installation, you must select either RGB or CCT
mode on the Parent Controller .
(see the Switch Mode button above,
in Fig 1)
See separate instruction sheets for further information on Tresco®
low voltage LED RGB and CCT lights, FREEDiM Parent Controllers
and Child Receivers, and Power Supplies.
Pairing the Remote Control to the Parent Controller
1 . First install the Parent Controller with either a RGB or CCT LED light system
and then turn on the Parent Controller .
2 . Check the mode on the Parent Controller and select either RGB or CCT mode
depending on the LED light system installed .
3 . On the Remote Control hit the ON button
R
G
B
Z1
Z2
3000K
3500K
5000K
.
- The small indicator light in top corner is now red, indicating that the Remote
Control is live and active (this light stays on for 30 sec .)
(see
Fig. 1
above)
.
4 . Using the Switch Mode button
R
G
B
Z1
Z2
3000K
3500K
5000K
, select either RGB or CCT mode . The red
indicator light underneath the Switch Mode button indicates RGB mode .
5 . On the Parent Controller press the Learning Key one time .
6 . Next on the Remote Control press the Zone 1 button
R
G
B
Z1
Z2
3000K
3500K
5000K
. The Zone 1 indicator
light underneath is now red
(see
Fig. 1
above)
.
7 . After you have hit the Zone 1 button, touch either the RGB Color Wheel or
CCT Slider . Lights will flash once indicating everything is paired .
Then repeat steps if adding Zone 2 or more Parent Controllers .
Note: Each zone can control 1 Parent Controller and up to 10 Child Receivers .
Each zone is independent and must be controlled separately from each
other .
(see more information and illustration on page 2)
Zone 1 Indicator Light
RGB Indicator Light
#
1
Zone 2 Indicator Light
(Instructions continued on page 2)