5 & 5.5 Fort Monkey Bar
Assembly
5 & 5.5 Playcenter M Bar
Assembly
***This step is only if you purchased a 5 or 5.5 Fort***. Line up Monkey Bar Overhead
countersunk holes with the holes below your 6 Hole Facia. Place a 3/4” Flatwasher over
a 1/2” x 7” Carriage Bolt and then insert thru the hole into the countersunk hole in the
Monkey Bar Overhead. Place a 1/2”
W
asher
, 1/2” Lockwasher over the 1/2” x 7” Car
-
riage Bolt end inside the Monkey Bar Overhead.
Thread the 1/2” Hex Nut on to the 1/2”
x 7” Carriage Bolt. Repeat this process on the other side. Now tighten the 1/2” Hex Nuts,
put on the 1/2”
Acorn Nut and lightly tighten. Do
not over tighten. Place Left Gusset Bracket and attach with 2 - 3/8” x 3 1/2” Hex Lag
Screw with 3/8” Flatwashers on them. Repeat this process for the Right Gusset Bracket
on other side.
Remove the 1/2” x 7” Carriage Bolt and Hardware from the Corner Post.
Then line
up Monkey Bar Overhead countersunk holes with the holes in the Playcenter as seen
above.
Place a 1/2”
W
asher over the 1/2” x 9” Hex Bolt and then insert thru the Front
Beam, then thru the Corner Post, and into the countersunk hole in the Monkey Bar
Overhead.
Place a 1/2”
W
asher
, 1/2” Lockwasher over the 1/2” x 9” Hex Bolt end in-
side the Monkey Bar Overhead.
Thread the 1/2” Hex Nut on to the 1/2” x 9” Hex Bolt.
Place
Right Gusset Bracket and attach with 2 - 3/8” x 3 1/2” Hex Lag Screw with 3/8”
Flatwashers on them.
On the other side place a 3/4” Flatwasher over a 1/2” x 7” Carriage Bolt and then insert
thru the hole into the countersunk hole in the Monkey Bar Overhead. Place a 1/2”
W
asher
, 1/2” Lockwasher over the 1/2” x 7” Carriage Bolt end inside the Monkey Bar
Overhead.
Thread the 1/2” Hex Nut on to the 1/2” x 7” Carriage Bolt. Now tighten the
1/2” Hex Nuts, put on the 1/2”
Acorn Nut and lightly tighten. Do not over tighten.
Place Left Gusset Bracket and attach with 2 - 3/8” x 3 1/2” Hex Lag Screw with 3/8”
Flatwashers on them.
HARDW
ARE NEEDED
UMH-12- 3/4” USS Flatwasher
-
(2)
UMH-8- 1/2” Split Lockwasher
-
(2)
UMH-1
1- 1/2” USS Flatwasher
-
(3)
UMH-3- 1/2” Hex Nut-
(2)
UMH-1- 1/2”
Acorn Nut-
(2)
UMH-2- 1/2” x 7” Carriage Bolt-
(2)
UMH-10- 3/8” USS Flatwasher
-
(4)
UMH-6- 3/8” x 3 1/2” Lag Screw-
(4)
UMH-13- 1/2” x 9” Hex Bolt-
(1)
HARDW
ARE NEEDED
UMH-12- 3/4” USS Flatwasher
-
(2)
UMH-8- 1/2” Split Lockwasher
-
(2)
UMH-1
1- 1/2” USS Flatwasher
-
(2)
UMH-3- 1/2” Hex Nut-
(2)
UMH-3- 1/2”
Acorn Nut-
(2)
UMH-2- 1/2” x 7” Carriage Bolt-
(2)
UMH-10- 3/8” USS Flatwasher
-
(4)
UMH-6- 3/8” x 3 1/2” Lag Screw-
(4)
UMB-3- (L) Gusset-
(1)
UMB-4- (R) Gusset-
(1)
UMH-2
UMH-12
UMH-1
1
UMH-8
UMH-3
UMH-1
UMB-4
UMB-3
UMH-6
UMH-10
UMH-13
UMH-1
1
UMH-1
1
UMH-8
UMH-3
UMH-1
UMB-4
UMH-10
UMH-6
UMH-6
UMH-10
UMH-2
UMH-12
UMH-1
1
UMH-8
UMH-3
UMH-1