manualshive.com logo in svg

Trebor MAGNUM 610R, Operation & Maintenance Manual, Page: 18 / 24

Share
Download
Trebor MAGNUM 610R Operation & Maintenance Manual Download Page 18

 

PAGE 18 

MAGNUM 610R PUMP OPERATION / MAINTENANCE MANUAL 

 

Figure 4-2 

  Insert suction sleeve, check ball and O-ring carefully into check bore. 

NOTE:

  The Suction Sleeves have a shoulder diameter larger than their body 

diameter. Additionally the Suction Sleeves when compared to the Discharge 
Sleeves have a thicker top region which acts as a robust contact point for the O-
rings.

 

  Repeat insertion process with the discharge sleeve, check ball and O-ring. 

  Repeat process for second check bore. 

  Replace check cap seals and tighten check bore caps to 50in-lbs. 

  Install shaft seals into shaft bore grooves. 

  Thread shaft into push plate until engagement with the shaft shoulder is 

achieved. Additionally apply a ¼” turn to ensure proper installation. 

  Insert shaft through shaft bore using shaft bullet as shown (This prevents 

damage to the TFE shaft seals and prevents dislodgement of shaft seals). 

Summary of Contents for MAGNUM 610R

























Reviews:

No comments