TRAXXAS.com
Traxxas, 6250 Traxxas Way, McKinney, TX 75070, Phone: 972-549-3000, Fax: 972-549-3011, e-mail: [email protected]
HKC20012-R02 Rev 210625
Pro Scale
®
Lighting
Installation Kit - 1979 Ford
®
Bronco
®
Installation
This kit contains the installation components necessary to adapt
the part #8036 Bronco LED Light Kit for full compatibility with the
Pro Scale Advanced Lighting Control system, part #6591 (part #8036
and 6591 sold separately).
If the 8036 LED light kit has already been installed,
it will be
necessary to remove the existing distribution block and mount in
the body and install the new Pro Scale Lighting Distribution Block
(part #6593, included with part #6591) using the new distribution
block mount supplied with this kit. These instructions assume the
8036 LED Light Kit has already been installed.
If you are installing the 8036 LED light kit for the first time,
then
follow the instructions included with the LED light kit except use
the Pro Scale Lighting Distribution Block along with the mounting
bracket supplied with this kit.
In either case above, you will also install the reverse lights harness
supplied with this kit alongside the tail light harness in the body.
See the wiring diagram on the reverse side for supplemental
information.
1. Remove the 2.6x8mm button-head screws (2) to remove the
installed distribution block and mount from the vehicle body
(Fig. A1)
.
2. Unplug the installed LED light wire harness connectors from the existing distribution block.
3. Install the new distribution block mount and secure with the 2.6x8 mm
button-head screws (2) from step 1 (Fig. A2).
4. Insert the LEDs on the included reverse lights harness into the tail light assemblies. The LEDs should snap into place. Route the wiring harness alongside
the brake lights harness in the body
(see Wiring Diagram on the reverse side)
. Remove the installed zip ties. New zip ties are provided to secure the wires
after the new harness is added. Secure the wiring to the body in the locations provided. The zip ties do not need to be tight; allow some extra length for
wire movement.
5. Plug all LED light wire harness connectors into the ports on the
Pro Scale
distribution block. Match the color band and/or letter indicator on the wire
harnesses with the corresponding color/letter of each port on the distribution block
(see chart below)
. Install the included double jumper into port F.
6. Use the included 2.6x8mm button-head screws (2) to secure the distribution block to the mount (Fig. A2).
Covers Part
#8032
Fig. A2
Kit contents:
• Distribution block mount (1)
• 2.6x8mm button-head cap screws (2)
• Reverse lights harness (1)
• Double jumper (1)
• Zip ties (5)
Tools required:
• 2.0mm hex wrench
2.6x8mm BCS
Visitez Traxxas.com/manuals pour télécharger
les instructions dans votre langue.
Visite la página Traxxas.com/manuals para
descargar el instrucciones en su idioma.
Auf Traxxas.com/manuals, können Sie
anleitung in Ihrer Sprache downloaden.
2.6x8mm BCS
Letter Color Description
Function
A
N/A
Reverse light harness
Back up light LEDs when vehicle is put in reverse
C
Red
Tail light harness
Tail lights, brake lights, and rear integrated turn signal LEDs
D
Blue
Rear side marker harness
Rear side marker LEDs
F
N/A
Rear integrated turn signal
jumper
Install jumper when using rear integrated turn signals
(single red LED for tail, stop, and turn)
G
White Headlight assembly harness Headlights and front marker light LEDs
H
White Front turn signal harness
Front turn signal light LEDs
Distribution Block LED Light Harness Ports
Fig. A1
PRO-SCALE
DISTRIBUTION
BLOCK
#XXXX
™
E
F
G
H
K
M
N
A
B
C
D
Part 6593
PRO SCALE
®
LIGHTING
DISTRIBUTION BLOCK
Wiring connectors for the
lights are labeled with
letters and/or colors.
Accessory Connectors
(not used with this kit)