background image

Safety Precautions

5

© Travis Industries

4080123

100-01174_002

Do  not  place  clothing  or  other
flammable  items  on  or  near
the  heater.    Because  this
heater  can  be  controlled  by  a
thermostat  there  is  a  possibility
of  the  heater  turning  on  and
igniting  any  items  placed  on
or  near  it.

AA

AA

AA

AA

A

Light  the  heater  using  the  built-
in  piezo  igniter.    Do  not  use
matches  or  any  other  external
device  to  light  your  heater.

Allow  the  heater  to  cool  before
carrying  out  any  maintenance
or  cleaning.

The  viewing  glass  should  be
opened  only    for  lighting  the
pilot  or  conducting  service.  Do
not  operate  with  cracked,
broken, or removed glass.

Any safety screen or guard
removed  for  servicing  must  be
replaced  prior  to  operating  the
heater.

Never  remove,  replace,  modify
or substitute any part of the
heater  unless  instructions  are
given  in  this  manual.    All  other
work must be done by a trained
technician.    Don't  modify  or
replace  orifices.

Operate  the  heater  according
to  the  instructions  included  in
this  manual.

If the main burners do not start
correctly  turn  the  gas  off  at  the
gas  control  valve  and  call  your
dealer  for  service.

The  pilot  flame  must  contact
the  thermopile  and
thermocouple  (see  the
illustration  to  the  left).    If  it  does
not,  turn  the  gas  control  valve
to  "OFF"  and  call  your  dealer.

AA

AA

AA

AA

This unit is not for use with
solid  fuel

Do  not  place  anything  inside
the  firebox  (except  the
included  fiber  logs).

If  the  fiber  logs  become
damaged,  replace  with  Travis
Industries log set.

This
Manual

Do  not  throw  this  manual  away.
This  manual  has  important
operating  and  maintenance
instructions  that  you  will  need
at  a  later  time.    Always  follow
the  instructions  in  this  manual.

Children  and  adults  should  be
alerted  to  the  hazards  of  high
surface  temperature  and
should  stay  away  to  avoid
burns  or  clothing  ignition.
Young  children  should  be
supervised when they are in
the same room as the heater.

Plug  the  heater  into  a  120V
grounded  electrical  outlet.    Do
not  remove  the  grounding  plug.

Don’t  route  the  electrical  cord
in  front  of,  over,  or  under  the
heater

Instruct  everyone  in  the  house
how to shut gas off to the
appliance  and  at  the  gas  main
shutoff  valve.    The  gas  main
shutoff  valve  is  usually  next  to
the gas meter or propane tank
and requires a wrench to shut
off.

Travis Industries, Inc. grants
no warranty, implied or stated,
for the installation or
maintenance of your heater,
and assumes no
responsibility of any
consequential  damage(s).

Summary of Contents for DVL Insert EF II













































Reviews: