manualshive.com logo in svg

Travis Industries DVL Insert EF II, Owner'S Manual, Page: 23 / 44

Share
Download
Travis Industries DVL Insert EF II Owner'S Manual Download Page 23

Finalizing the Installation

23

© Travis Industries

4080123

100-01174_002

Step 2 - Install the twigs, ember chunk, kibbles, and rock wool

AA

AA

AA

A

A

A

AA

AA

AA

A

A

Place the left and right  

twigs as shown.

AA

AA

A

AA

AA

AA

AA

A

A

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

Place the ember 

chunk as shown.

AA

AA

AA

A

A

AA

AA

AA

A

A

Place the kibbles in a random 

pattern.  Make sure to place 

them over any exposed 

screws or metal to create a 

desirable effect.  Do not place 

kibbles directly over the 

burner holes.

Installing the Rock Wool:

The rock wool comes in one clump.  Tear off 

“dime” sized clumps and flatten.  Then pull on 

the wool to create gauze-like pieces.  Place them 

near some of the burner holes.  The wool glows 

best when very thin and porous.

NOTE: We recommend using very little rock 

wool, especially in LP or high-altitude 

installations.

AAAAA

AAAAA

A

Summary of Contents for DVL Insert EF II













































Reviews:

No comments