Travis Industries 430 Mod-Fyre GSR2 Manual Download Page 1

 

430 Mod-Fyre™ 

GSR2 Insert 

Manual 

 

 

 

 WARNING: FIRE OR EXPLOSION HAZARD 

Failure to follow safety warnings exactly could result in serious injury, death, or property damage. 

 

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any 
other appliance. 

WHAT TO DO IF YOU SMELL GAS

 

• Do not try to light any appliance. 
• Do not touch any electrical switch; do not use any phone in your building. 
• Leave the building immediately 
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's 

instructions. 

• If you cannot reach your gas supplier, call the fire department. 

-  Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

 

 

 

 

HOT GLASS 

WILL CAUSE 

BURNS

 

DO NOT TOUCH 

GLASS 

UNTIL COOLED

 

NEVER 

ALLOW CHILDREN 

TO TOUCH GLASS

 

A barrier designed to reduce the risk of burns from 
the hot viewing glass is provided with this appliance 
and shall be installed for the protection of children 
and other at-risk individuals.  

Tested and Listed by  

 

Report# G100518003PRT-002 

ANSI Z21.88-2017 

CSA 2.33-2017 

 

Direct Vent Fireplace Insert 

 

Masonry or Factory-Built 
(Metal) Wood-Burning 
Fireplace 

 

Residential or Mobile Home 

 

 

This appliance may be installed in an aftermarket, permanently located, manufactured home 
(USA only) or mobile home, where not prohibited by local codes. 
This appliance is only for use with the type of gas indicated on the rating plate.  A conversion 
kit is supplied with the appliance. 

 

INSTALLER: Leave this manual with the appliance.  
CONSUMER: Retain this manual for future reference. 

French language manuals at  

fireplacex.com. or lopistoves.com   

Manuels de langue Française à  

f

ireplacex.com. or lopistoves.com

 

 

Travis Industries, Inc. 

12521 Harbour Reach Dr., Mukilteo, WA  98275 

www.travisproducts.com

 

 Copyright 2021, T.I.  

$10.00        5/20/2021 

100-01558 

 

Summary of Contents for 430 Mod-Fyre GSR2



































































Reviews: