Transition Networks
EO2Pxx4052-111 Quick Start Guide
33705 Rev. E
Page
1
of
2
EO2Pxx4052-111 Quick Start Guide
Introduction
Transition Networks’ EO2Pxx4052-111 Ethernet Extenders With PoE+ (EO2P) allow up to
1000Mb data communication and deliver SELV (Safety Extra Low Voltage) power over twisted
pair wiring to a connected IP device. Each installation requires a pair of these devices, one
Local Unit at the network source and one Remote Unit near the connected PoE device.
See the full EO2P User Guide for Product Numbers, Applications, Configuration Examples, Features, Package Contents,
Port Descriptions, Web Config pages, Technical Specs, Warranty and Compliance info, Messages, and Troubleshooting.
Installation
Note
: See the EO2P User Guide for important Cautions and Warnings including Operating temperature, Air Flow,
Mechanical Loading, Circuit Overloading, etc.
Mounting
Install the EO2P units indoors (or in an appropriately rated enclosure).
Securely mount the EO2P units. Do not support the EO2P units by the attached cables.
Use any of the Mounting options to mount the EO2P unit. See the User Guide for options.
Front Panels
: Local Device (top right) Remote Device (bottom right):
Network Connections
Network Connection
: The EO2PSE4052-111 offers a Combo (Shared) port for connecting to either copper or fiber
network equipment. In terms of copper versus fiber port selection / priority, only one port can be active at any given
time; by default the SFP port takes precedence over the copper port (configurable on the Ethernet Web GUI page).
SFP / Fiber Connection: The EO2P lets you install an SFP optic of your choice in order to make a fiber connection. The
EO2P has a single SFP port. The SFP port supports any MSA compliant 100/1000Base-X SFP module. For temperatures
above +50 ̊ C, industrial SFP modules (+85 ̊C) must be used. Install and connect Single-strand or Two-strand Fiber cable.
Ethernet Cable Connection: Connect the EO2PSE4052-111 RJ45 Ethernet jack to the EO2PD, camera or other network
equipment using a standard Ethernet cable.
Power over Ethernet
: Using the PoE option, the EO2PSE4052-111 can automatically enable delivery of up to 30 watts of
power to the EO2PD4052-11. The EO2PD4052-111 can supply up to 25.5 Watts of PoE (IEEE 802.3at-class) power to a
connected powered device.
Warning
: Do not plug a network cable into the Power Out or Power In RJ-45 jacks.
Remote
: Local Power Source: DIN or TB (48V@45W). Remote POE-PSE: IEEE 802.3at - Class 4. 802.3at PSE Power Out: 30
W at Remote Unit; 25.5W Power at PD.
Extension Data
and Power Connection
Install the RJ-45 Copper Cable
:
1.
Locate a 10/100/1000Base-TX compliant copper cable with male RJ-45 connectors
installed at both ends.
2.
Connect the RJ-45 connector at one end of the cable to the EO2P 10/100/1000Base-RJ-45 port.
3.
Connect the RJ-45 connector at the other end of the cable to the 10/100/1000Base-RJ-45 port on the device (camera,
WAP, etc.) that you wish to connect and power.
RJ45 Connection
: Install an RJ45 connectorized cable between Local unit DATA + PWR OUT and the Remote Unit DATA +
PWR IN RJ45 connectors. The cable can be fully- or partially pinned. See the User Guide for Cable configurations.
2-Wire Connection
(Local to Remote Unit): Connect the EO2PSE4052-111 unit’s 2-wire
connector to the 2-wire
twisted pair cable. The 2-wire connector should only be used to
connect a Local unit to a Remote Unit. The EO2Pxx4052-111 is not compatible with other
equipment such as analog video amplifiers. Note that the 2-wire cable may be shielded
twisted-pair (STP) or unshielded twisted-pair (UTP) wire, but it must be twisted pair wire.
