2
24-hour Technical Support:
1-800-260-1312
-- International:
00-1-952-941-7600
CSDTF30xx-11x
*
Typical maximum cable distance. Actual distance is dependent upon the
physical characteristics of the network. (TX) = transmit (RX) = receive
Part Number
Port One -
Copper
Port 2 -
Simplex Fiber Optic
CSDTF3029
-115
and CSDTF3029
-116
are intended to be
installed in the same link where one is the local converter and
the other is the remote converter.
CSDTF3029
-117
and CSDTF3029
-118
are intended to be
installed in the same link where one is the local converter and
the other is the remote converter.
CSDTF3029-115
75 ohm BNC coax
100 m (328 ft.)*
SC, 1310 mn (TX)/1550 nm (RX)
single mode, 20 km (12.4 miles)*
CSDTF3029-116
75 ohm BNC coax
100 m (328 ft.)*
SC, 1550 mn (TX)/1310 nm (RX)
single mode, 20 km (12.4 miles)*
CSDTF3029-117
75 ohm BNC coax
100 m (328 ft.)*
SC, 1310 mn (TX)/1550 nm (RX)
single mode, 40 km (24.8 miles)*
CSDTF3029-118
75 ohm BNC coax
100 m (328 ft.)*
SC, 1550 mn (TX)/1310 nm (RX)
single mode, 40 km (24.8 miles)*
Installation
CAUTION:
Wear a grounding device and observe electrostatic discharge
precautions when setting the jumper.
Failure to observe this caution could
result in damage to, and subsequent failure of, the media cverter.
Set the Hardware/Software Jumper
The jumper is located on the circuit board. Use needle-nose pliers to move
the jumper to the desired position.
Hardware
The media converter mode is
determined by the switch settings.
Software
The media converter mode is
determined by the most-recently saved,
on-board microprocessor settings.
Software Mode
Hardware Mode
H
S
H
S
E1 Configuration
(switch 4)
IMPORTANT:
Switch 4
MUST
be set to
the “down” position to set the media
converter for E1 configuration.
E1 Configuration (down)
1
3 4
2
IMPORTANT !
-- Click the
“Transition Now”
link for a live Web chat.
3
Switch 2. Fiber -- Transmit All Ones
Up
- Disables the Transmit All Ones
function on the fiber interface.
Down
- Transmits an “all ones” pattern
on the fiber interface when the signal
detect on the
coax
interface is lost.
Switch 3. Not in use
Fiber - Transmit All Ones - Disabled
Fiber - Transmit All Ones - Enabled
1
3 4
2
Installation
-- Continued
CAUTION:
Wear a grounding device and observe electrostatic discharge
precautions when setting the switches.
Failure to observe this caution could
result in damage to, and subsequent failure of, the media converter.
Set the Configuration Switches
The configuration switches are located on the side of the media converter.
Use a small, flat-blade screwdriver or a similar device to set the recessed
switches.
Transmit All Ones
(switches 1 & 2)
The Transmit All Ones function allows the insertion of an “all ones” pattern on
the interface when the
signal detect
is lost, creating an alarm condition at the
device connected to the interface.
Switch 1. Coax -- Transmit All Ones
Up
- Disables the Transmit All Ones
function on the coax interface.
Down
- Transmits an “all ones” pattern
on the coax interface when the signal
detect on the
fiber
interface is lost.
3 4
1 2
Down
Not Used
Up
key:
Coax - Transmit All Ones - Disabled
Coax - Transmit All Ones - Enabled
1
3 4
2
