MEDIA CONVERTER TECHNICAL SPECIFICATIONS
Standards
ANSI/ATA 878
Case dimensions
4.75" x 3.0" x 1.0"
(119mm x 76mm x 25mm)
Shipping Weight
2 pounds
(0.9 kilograms)
Environment
Temperature:
0-40°C (32° to 104° F )
Humidity
10-90%, non condensing
Altitude
0-10,000 feet
Warranty
Five years
Power Supply Requirements
Replace power supply with only the equivalent
input rating (see below) and output rating (regulated 9VDC at 0.5 A).
TN PN
Requirement
Location
3525
240 volts, 50 hertz
United Kingdom
3525
230 volts, 50 hertz
Europe
3518
120 volts, 60 hertz
USA/Canada/Mexico
3514
100 volts, 50-60 hertz
Japan
3525
240 volts, 50 hertz
Australia
NOTE: This product also can be powered by the Transition Networks E-MCR series media
converter rack.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.
Compliance Information
UL Listed
C-UL Listed (Canada)
CISPR/EN55022 Class A
FCC Regulations
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on
the radio interference regulations of the Canadian Department of Communications.
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Copyright Restrictions
© 1999 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.
Trademark Notice
All registered trademarks and trademarks are the property of their respective owners.
33053.A
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten
verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur
Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen
einschliesslich der gegenseitigen Anerkennung ihrer Konformität.
The TRANSITION Networks ARCNET
®
RJ-11 Copper/Fiber Media Converter
(AR-CF-01) extends the signal distance of an ARCNET
®
segment or node
link.
AR-CF-01 series media converters _________________
STATUS LEDS
Power
Steady green LED
indicates connection
to external AC power.
UTP/STP Blinking green LED
indicates network
traffic on unshielded or shielded twisted-pair link.
Fiber
Blinking green LED indicates network traffic on fiber link.
Minneapolis, MN 55344 USA
ARCNET
®
RJ-11 Copper/Fiber
Media Converter
AR-CF-01, AR-CF-01(SC), AR-CF-01(SM)
USER’S GUIDE
10BASE-T
RX
TX
Fiber
Power
U T P / S T P
AR-CF-01
Provides an RJ-11
twisted-pair connector to
copper cable and a set of
RX (receive) and TX
(transmit) ST connectors
to multimode fiber-optic
cable.
AR-CF-01(SC)
Provides an RJ-11 twisted-pair
connector to copper cable and an
RX (receive) and TX (transmit) SC
connector to multimode fiber-optic
cable.
AR-CF-01(SM)
Provides an RJ-11 twisted-pair
connector to copper cable and an
RX (receive) ST and TX (transmit)
SC connector to singlemode fiber-
optic cable.
AR-CF-01
ArcNet
Fiber to Twisted Pair
Media Converter
®
