background image

System Guide

TransCore Proprietary

 iv

List of Figures

Figure   2 – 1  MPRX End Views ........................................................................................................2–2
Figure  2 – 2  Tag and Antenna Orientation (horizontal polarization) .....................................2–4
Figure 2 – 3 Horizontally Polarized Tag ........................................................................................................2–5
Figure  2 – 4  Antenna Location Relative to Tag Position ..........................................................2–6
Figure  2 – 5  Location of Host Port on MPRX..............................................................................2–11
Figure  2 – 6  Pin Assignments for Host Connector ...................................................................2–11
Figure  2 – 7  Location of Sense Port on MPRX .......................................................................... 2–12
Figure  2 – 8  Pin Assignments for Sense Connector ............................................................... 2–12
Figure  3 – 9  Clear Zone –Side View ............................................................................................. 3–4
Figure  3 – 10  Clear Zone –End View ............................................................................................ 3–4
Figure 3 – 11 Mounting Location Examples ..................................................................................3–5
Figure  3 – 12  Tag Placement Window for Locomotives – Right Front .....................................3–6
Figure  3 – 13  Right Front Placement of Tag on Locomotive .................................................... 3–7
Figure  3 – 14  Tag Placement Window Location for Locomotives — Left Rear ...................... 3–7
Figure  3 – 15   Optimal Tag Placement for Locomotives ...........................................................3–8
Figure  3 – 16  Tag Placement Window Location for Rail Cars –“A” Right Side ...................3–9
Figure  3 – 17  Tag Placement Window Location for Rail Cars -“B” Left Side ...........................3–9
Figure  3 – 18  Optimal Tag Placement for Rail Cars ................................................................... 3–10
Figure  3 – 19  Tag Placement Window Location for Tank Cars –“B” Left Side ...................3–11
Figure  3 – 20   Optimal Tag Placement for Tank Cars ..............................................................3–11
Figure   4 – 1   Wiring for Audible Circuit Tester ........................................................................... 4–4
Figure  4 – 2  Connect RF N-type Load or Attenuator to Reader Cable End .......................4–5
Figure  4 – 3  Short Load to Earth Ground .....................................................................................4–5
Figure  4 – 4  MPRX Showing Antenna Ports ................................................................................4–6
Figure  4 – 5  Location of MPRX Ground Stud .............................................................................. 4–7
Figure  4 – 6  Location of Communications/Power Port on MPRX .........................................4–8
Figure  4 – 7  MPRX Outer Dimensions and Mounting Hole Locations (not to scale) ....... 4–10
Figure  4 – 8  Sample Read Zone Marking Pattern ..................................................................... 4–15
Figure   8 – 1  Connection Description Dialog Box ........................................................................... 8–4
Figure  8 – 2   Phone Number Dialog Box ........................................................................................... 8–4
Figure  8 – 3  COM 1 Properties Dialog Box ........................................................................................ 8–5
Figure  8 – 4  Hyper Terminal Main Screen....................................................................................8–6
Figure 8 – 5 Sign-on Message ........................................................................................................ 8–7

Summary of Contents for MPRX

















































































































































































































Reviews: