background image

Factory-Mounted Unit Options

RT-SVX33E-EN

27 

Powered/Unpowered 
Convenience Outlet

Powered Convenience Outlet Powered 
Option (FIYCOPO)

When the powered convenience outlet option is installed, 
the unit will include a dedicated transformer located in the 
evaporator section of the unit. Additionally, a service 
receptacle disconnect switch will be provided on the side 
wall of the evaporator section. The service receptacle 
switch is shipped in the OFF position. 

The powered outlet comes completely wired from the 
factory except for 208 volt applications. 

1.

For 208 volt applications, disconnect and tape the blue 
230 volt wire.

2. Then connect the brown 208 volt wire.

WARNING

Hazardous Voltage w/Capacitors!

Disconnect all electric power, including remote 
disconnects and discharge all motor start/run 
capacitors before servicing. Follow proper lockout/
tagout procedures to ensure the power cannot be 
inadvertently energized. Verify with an appropriate 
voltmeter that all capacitors have discharged. Failure to 
disconnect power and discharge capacitors before 
servicing could result in death or serious injury. 

For additional information regarding the safe discharge 
of capacitors, see PROD-SVB06A-EN 

WARNING

Proper Field Wiring and Grounding 
Required!

All field wiring MUST be performed by qualified 
personnel. Improperly installed and grounded field 
wiring poses FIRE and ELECTROCUTION hazards. To 
avoid these hazards, you MUST follow requirements for 
field wiring installation and grounding as described in 
NEC and your local/state electrical codes. Failure to 
follow code could result in death or serious injury. 

Figure 21. Wiring schematic 12½ through 25 ton options

Summary of Contents for Voyager WS 150-24













































Reviews: