background image

Product Application

This Comfort Control provides electronic control of 24 VAC single-stage heating  
and cooling systems.

System Types

•  Gas, oil or electric heat with  

air conditioning

•  Warm air, hot water, high-efficiency 

furnaces, heat pumps

•  Heat only with fan

•  Cool only

Power 

•  Common wire only

•  Common wire with battery backup

Changeover Options

•  Selectable manual or  

auto-changeover modes

System Settings

•  Heat, Off, Cool, Auto

Fan Settings

•  Auto, On

Must be installed by a trained, experienced technician

•  Read these instructions carefully. Failure to follow these instructions can  

damage the product or cause a hazardous condition.

•  Check the ratings in this booklet to verify that this product is suitable for your 

application (see page 12).

•  Always test for proper operation after installation (see page 8).

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before  

beginning installation.

MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do not 

place the old control in the trash. Contact your local waste management authority 

for instructions regarding recycling and proper disposal.

Summary of Contents for TCONT600AF11MA

















Reviews: