20
DISCONNECT ALL ELECTRIC POWER
INCLUDING REMOTE DISCONNECTS
BEFORE SERVICING.
FAILURE TO DISCONNECT POWER
BEFORE SERVICING CAN CAUSE
SEVERE PERSONAL INJURY OR DEATH.
IMPORTANT
USE COPPER CONDUCTORS ONLY
TO PREVENT EQUIPMENT DAMAGE.
UNIT TERMINALS ARE NOT DESIGNED
TO ACCEPT ANY OTHER WIRING.
WARNING
HAZARDOUS VOLTAGE!
3
3
2
AND/OR DASHED DEVICE OUTLINES INDICATE
WIRING BY OTHERS. DASHED LINE ENCLOSURES
COMPONENTS PROVIDED BY THE FIELD. PHAN TOM
LINE ENCLOSURES INDICATE ALTERNATE
SOLID LINE INDICATES FACTORY WIRING.
REMOVE JUMPER WHEN TEMPERATURE CONTROLLER
REMOVE JUMPER TO INTERFACE WITH EVF
CIRCUITRY OR AVAILABLE SALES OPTIONS.
IS INSTALLED
INTERLOCK
1
NOTES:
DASHED LINES INDICATE RECOMMENDED FIELD
2
2
CLEAR THE MEMORABLE ERROR.
THE 7-SEG WILL OFF FOR 2 SECONDS BEFORE DISPLAY THE
EACH LOCKOUT. AFTER THAT THE 7-SEG WILL OFF FOR
MOMORABLE ERROR CODES THAT ARE THE CAUSES OF
PRESS SW3 BUTTON FOR SHOW THE MEMORABLE ERROR.
2 SECONDS AND RETURN TO DISPLAY THE EXISTING
THEY ARE DISPLAYED 2 SECOND EACH.IF THERE IS NOT ANY
ERROR/STATUS CODES.IF MORE THAN 1 ERROR HAPPENS,
MEMORABLE ERRORS,THE NORMAL CODE WILL BE DISPLAYED.
PRESS AND HOLD SW3 BUTTON FOR 4 SECONDS TO
4
EVF INTERLOCK
T1 T2
TB
T3
MCB
TERMINATION (CONTROL)
32
33
30
N
TO TEMP. CONTROLLER STEP 2
TO TEMP. CONTROLLER STEP 1
RAUP MODEL ONLY
- NO AC SIGNAL AT INPUTS
- CONTACT INPUTS ONLY
WARNING :
COM 0
JUMPER
JUMPER
HMWT 4
COM 0
HMWT 3
OL 4
OL 3
HPCO 2
COM 0
JUMPER
JUMPER
JUMPER
S4
LPCO 2
COM 0
COM 0
S3
S2
COMP. : START-UP TIMING
A CIRCUIT A-C1 ON DELAY TIME = 1 min
A CIRCUIT A-C2 ON DELAY TIME = 2 min
TYPICAL WIRING FOR RAUP 250
SYSTEM RESET : = RESET SYSTEM ON ERROR
RESET 2 = RESET CIRCUIT B ON ERROR
RESET 1 = RESET CIRCUIT A ON ERROR
COM 0
JUMPER
JUMPER
HMWT 2
S1
-
COM 0
HMWT 1
OL 2
38
39
40
39
LPCO 1
OL 1
HPCO 1
COM 0
INPUT
J1
FAN FOR
RESET 2
RESET 1
SYSTEM RESET
A CIRCUIT
COMPRESSORS
LIGHT
TRIP
J5
N
ALM/NO
ALM/NC
J4
COM
L (240 V)
B-C3
C5
COM 5
COM 4
B-C4
COM 3
33
36
T2
A-C1
COM 2
A-C2
COM 1
OUTPUT
J3
33
35
33
34
T3
C5
A-C2
A-C1
-
NORMAL
Error Description
7 SEGMENT DISPLAY CODE TABLE
OL 1 Error
OL 2 Error
HMWT 2 Error
HMWT 1 Error
HPCO 1 Error
LPCO 1 Error
OL 4 Error
OL 3 Error
HMWT 3 Error
HPCO 2 Error
HMWT 4 Error
LPCO 2 Error
THERMOSTAT STATUS
H1
S1 - S4
t4
H2
O3
O4
t3
L2
t2
t1
O2
O1
7 Segment Display
--
L1
CIRCUIT B
CIRCUIT A
RESET 3
STARTER CONTROLLER MODULE - I/O WIRING :-RAUP250
CONTR
O
L BO
X
C1
C2
INPUT: USE BLACK COLOR 0.5 SQMM.
HPCO1
LPCO1
TX1
240V/21, 8V
OUTPUT: USE BLACK 1 SQMM.
Termination Diagram
Schematic &
RAUP 250
