background image

6

PTAC-SVX01C-EN

Pre-Installation

Pre-Installation 
Considerations

Before beginning  installation, make 
the following considerations:

1.

Verify the wall opening is in the 
correct location and the 
correct size.

2.

Drill mounting holes on both 
sides of the wall sleeve, if 
equipment requires any of the 
following options: subbase, 
leveling legs, or hydronic heat 
kit. 

If dimension A in 

Figure 2

 is at or 

near the minimum specified in 

Table 2, p. 7

, accessory options 

should be mounted to the sleeve 
prior to installing the sleeve in 
the wall. Otherwise, there may 
not be enough access room for 
the tools used to mount the 
accessories to the wall sleeve.

3.

If additional wall sleeve support 
is required, the leveling leg 
accessory kit or a subbase kit 
that includes leveling legs can be 
used to provide extra support.

4.

If installing in a concrete or 
masonry wall, you must provide 
a lintel in the wall opening for 
support. Do not use the wall 
sleeve as a lintel. 

See 

Figure 1

 for a typical lintel 

construction.

5.

When installing in walls that are 
deeper than 13 1/2 inches, use an 
extended wall sleeve. A sleeve 
without the proper depth will 
require special care to prevent 
problems with rain water, 
condensate drainage, and intake/
discharge air. 

Figure 1.

Typical Installation 
framing with lintel

Under these circumstances, 
careful jobsite analysis and 
cautions are required. Consult 
your local HVAC representative 
before attempting such 
installations.

Checklist

The following checklist provides an 
overview of the factory-
recommended pre-installation 
considerations. Follow the 
procedures in this section to ensure 
the installation is complete and 
adequate for proper unit operation. 
Verify this checklist is complete 
before beginning unit installation.

If unit arrives shipped on its side, 
do not accept.

Verify the unit size and tagging 
with the unit nameplate to 
ensure the correct unit is 
received.

Inspect the unit for possible 
shipping damage and make any 
necessary claims with the freight 
delivery company immediately.

Verify the installation location is 
free of airflow obstructions, such 
as curtains, furniture, trees, or 
other objects that may block 
airflow to and from the unit.

WARNING

Fire Hazard!

Do not use extension cords. Using 
extension cords could cause a fire.

Make provisions for correct 
supply power and that the 
electrical receptacle is within 52 
inches of the lower right corner 
of the equipment. 

Ensure the unit wall opening is 
level.

Ensure adequate sealing and 
insulation is around the wall 
sleeve.

Figure 2.

Minimum unit clearance

Table 1.

 Minimum interior and exterior 
projections

Figure 3.

Minimum wall opening 
dimensions

42 1/2” min

.

Finished
Floor

16 1/4” min.

Dimension B

Pre-Installation

Summary of Contents for PTAC-SVX01C-EN





















































Reviews: