background image

RT-SVX46G-EN

47 

Maintenance

Monthly Maintenance

Before completing the following checks, turn the unit OFF 
and lock the main power disconnect switch open.

Filters

Inspect the return air filters. Clean or replace them if 
necessary. If included, leave filter removal tool in unit. 
Refer to the unit Service Facts for filter information.

Return Air Smoke Detector Maintenance

Note:

Consult smoke detector manufacturer if daisy 
chaining is required.

Airflow through the unit is affected by the amount of dirt 
and debris accumulated on the indoor coil and filters. To 
insure that airflow through the unit is adequate for proper 
sampling by the return air smoke detector, complete 
adherence to the maintenance procedures, including 
recommended intervals between filter changes, and coil 
cleaning is required.
Periodic checks and maintenance procedures must be 
performed on the smoke detector to insure that it will 
function properly. For detailed instructions concerning 
these checks and procedures, refer to the appropriate 
section(s) of the smoke detector Installation and 
Maintenance Instructions provided with the literature 
package for this unit.

Condensate Overflow Switch

During maintenance, the switch float (black ring) must be 
checked to ensure free movement up and down.

Cooling Season

Check the unit’s drain pans and condensate piping to 
ensure that there are no blockages.

Inspect the evaporator and condenser coils for dirt, 
bent fins, etc. If the coils appear dirty, clean them 
according to the instructions described in “Coil 
Cleaning” later in this section.

Manually rotate the condenser fan(s) to ensure free 
movement and check motor bearings for wear. Verify 
that all of the fan mounting hardware is tight.

Inspect the F/A-R/A damper hinges and pins to ensure 
that all moving parts are securely mounted. Keep the 
blades clean as necessary.

Verify that all damper linkages move freely; lubricate 
with white grease, if necessary.

Check supply fan motor bearings; repair or replace the 
motor as necessary.

Check the fan shaft bearings for wear. Replace the 
bearings as necessary. 

Check the supply fan belt. If the belt is frayed or worn, 
replace it. Refer to the “Fan Belt Adjustment” section 
for belt replacement and adjustments.

Verify that all wire terminal connections are tight.

Remove any corrosion present on the exterior surfaces 
of the unit and repaint these areas.

Generally inspect the unit for unusual conditions (e.g., 
loose access panels, leaking piping connections, etc.)

Make sure that all retaining screws are reinstalled in 
the unit access panels once these checks are complete.

With the unit running, check and record the: ambient 
temperature; compressor suction and discharge 
pressures (each circuit); superheat (each circuit); 

WARNING

Hazardous Service Procedures!

Failure to follow all precautions in this manual and on 

the tags, stickers, and labels could result in death or 

serious injury.

Technicians, in order to protect themselves from 

potential electrical, mechanical, and chemical hazards, 

MUST follow precautions in this manual and on the 

tags, stickers, and labels, as well as the following 

instructions: Unless specified otherwise, disconnect all 

electrical power including remote disconnect and 

discharge all energy storing devices such as capacitors 

before servicing. Follow proper lockout/tagout 

procedures to ensure the power can not be 

inadvertently energized. When necessary to work with 

live electrical components, have a qualified licensed 

electrician or other individual who has been trained in 

handling live electrical components perform these 

tasks.

WARNING

Rotating Components! 

During installation, testing, servicing and 

troubleshooting of this product it may be necessary to 

work with live and exposed rotating components. Have 

a qualified or licensed service individual who has been 

properly trained in handling exposed rotating 

components, perform these tasks. Failure to follow all 

safety precautions could result in rotating components 

cutting and slashing technician which could result in 

death or serious injury. 

WARNING

Hazardous Voltage!

Failure to disconnect power before servicing could 

result in death or serious injury. Disconnect all electric 

power, including remote disconnects before servicing. 

Follow proper lockout/tagout procedures to ensure the 

power can not be inadvertently energized. 

Summary of Contents for Precedent YZC036E





























































Reviews: