Name and function of wireless remote control
ON/OFF button
Remote control
Signal transmitter
AUTO
COOL
DRY
FAN
(
)
●
Press this button to set up the clock time.
The and time display will begin to blink.
Adjust the time by pressing the
or
buttons. Press and hold the
button to change the time
value quickly. Press this button once
again to fix the time setting and exit the
clock set up.
Note: If a button is not pressed within 5
seconds (while the display is blinking) the
clock set up will exit and the setting will
not be saved.
CLOCK button
CLOCK
●
Press this button to toggle between a display
of the indoor set point, indoor room
temperature and outdoor temperature (outdoor
t
emperature
is only available on select models).
TEMP button
TEMP
Do not drop or throw the remote control; Do not let any liquid in the remote control.
Note: Be sure that there are no obstructions between receiver and remote controller;
Do not put the remote control directly in sunlight or any place where it is very hot.
●
Each time you press this button, a mode is
selected in a sequence that goes from AUTO ,
COOL, DRY, FAN and HEAT*.
MODE button
MODE
After the unit is turned on, the default operating
mode will be AUTO. In the AUTO mode, the indoor
set point will not be displayed as the unit will
automatically select the suitable operating mode
and temperature set point to make the room
temperature comfortable.
●
This button is used for setting Fan Speed in
the sequence that goes from AUTO, Low,
Medium-Low, Medium, Medium-High, High
then back to AUTO.
NOTE: Not all fan speeds are available on all units.
FAN button
FAN
Operation of wireless remote control
●
Press to start or stop operation. Press
this button to turn on the unit. Press this
button again to turn off the unit. Turning
the unit off will cancel any sleep, quiet,
or timer functions.
HEAT
Once the unit is turned on, the indoor
set point is the default temperature
displayed.
Medium fan
Low fan
High fan
●
Press this button to turn the indoor unit
display on or off. When the unit is turned
on
,
the default is to have the unit display on.
LIGHT button
LIGHT
Medium-low fan
Medium-high fan
Note: Dry mode uses the low fan speed.
-1-
*only for models with heating function
AUTO
TEMP button
or
CLOCK button
MS-SVU052A-EN 04/14
timer on or timer off.
Guide for operation- general operation
Operation of wireless remote control
★
This function allows removal of moisture on the evaporator of the indoor unit after
the unit has stopped. X-FAN is not available in AUTO, FAN or HEAT mode.
About X-FAN function
1. Having set X-FAN function on: After turning off the unit by pressing ON/OFF button
indoor fan will continue running for about 10 min at low speed. During this time
press X-FAN button again to stop the indoor fan sooner.
2. Having set X-FAN function off: After turning off the unit by pressing ON/OFF button,
the complete unit will be turned off immediately.
Introduction for special function
When AUTO RUN mode is selected, the set point temperature will not be displayed on the
LCD. The unit will be compared with the room temperature to automatically select the suitable
running method to achieve the desired set point.
About TURBO function
★
★
About AUTO RUN
1. Press SLEEP button, to set sleep.
2. Press TIMER ON and TIMER OFF button, can set the scheduled
3. Press LIGHT button, to control the light on and off of the unit display.
(This function may be not available for some units).
4. Press TURBO button, to select the ON and OFF of TURBO function.
close automatically.)
5. Press or buttons to select the swing.
4. Press FAN button, to set the fan speed, can select AUTO FAN, LOW,
MEDIUM-LOW, MEDIUM, MEDIUM-HIGH and HIGH. (NOTE: Not all fan speeds are available
for all units)
3. Press or
button, to set the desired temperature (It is unnecessary to set the temp.
at AUTO mode.)
2. Press MODE button, select desired running mode.
will start to run. (Note: When it is powered OFF, the guide louver of main unit will
1. After the unit is installed and electricity is connected, press ON/OFF button, the unit
Guide for operation- Optional operation
-6-
When selecting this function the unit will run at the highest fan speed to cool or heat quickly
so that the room temperature reaches the desired set point as soon as possible.
MS-SVU052A-EN 04/14
Press
and
buttons simultaneously to lock or unlock the
keypad.
If the
remote controller
flicker three times. If the
keypad
is unlocked, the mark will disappear.
1. Press swing up and down button continuously more than
two seconds
,
and
the main unit will swing back
and forth from up to down
.
Release
the button,
and the
unit will stop swinging and
current
position of guide louver will be kept.
2. Under swing up and down mode, when the status is switched from off to , press this
button again
two seconds
later,
status will switch to off
,
press this button again
within
two seconds. T
he change of swing status will also depend on the circulation sequence stated above.
★
★
★
★
About swing up and down
1. Press swing left and right button continuously more than
two seconds,
the main unit will swing back
and forth from left to
right.
Release
the
button
,
and the
unit will stop swinging and
current
position of guide louver will be kept.
2. Under swing left and right mode, when the status is switched from off to , press this
button again
two seconds
later,
status will switch to off
,
press this button again
within
two seconds,
the change of swing status will also depend on the circulation sequence stated above.
★
About swing left and right
About lock
Operation of wireless remote control
About switch between Fahrenheit and Centigrade
When unit is powered
off, press MODE and
use
buttons simultaneously to switch
℃
and
℉
.
★
About Quiet function
If Auto Quiet mode has been selected, after the room temperature
has reached the set point
temperature or
10 minutes
later, the AC will immediately enter into the Quiet running
mode
, at
★
this time the fan speed is not adjustable.
About Sleep function
Under the Fan and Auto mode, the Sleep function cannot be set up, under
DRY
mode, only Sleep 1 can be selected. Select and enter into any kind of Sleep mode, the
★
Quiet function will be
started. Other
Quiet status could be optional and turned off.
Press “TEMP” and “CLOCK” simultaneously in COOL mode to start energy-saving function.
The display screen
on the remote controller displays “SE”. Repeat the operation to quit the function.
Press “TEMP” and “CLOCK” simultaneously in HEAT mode to start
8
℃
Heating
.
on the remote controller displays “ ” and a selected temperature of
“ 8
℃
(46°F)
” (46 if
Fahrenheit is adopted). Repeat the operation to quit the function.
Combination of " TEMP" and "CLOCK" buttons : About 8
Combination of " TEMP" and "CLOCK" buttons : About Energy-saving Function
℃
(46°F)
Heating Function
℉
(46°F)
-
7
-
Function.
The display screen
is locked, the icon will be
displayed.
Press any key and the lock icon will
MS-SVU052A-EN 04/14
●
●
●
●
●
●
●
Operation of remote control
Changing batteries and notices
1.Lightly press the place with , along the arrowhead
direction to push the back cover of wireless remote control.
(As shown in Fig 1. )
2.Take out the old batteries.
3.Insert two new AAA1.5V dry batteries, and pay attention
Fig.1
Fig.2
NOTE:
When changing the batteries, do not use old or
different batteries, otherwise, it can cause malf-
unction of the wireless remote control.
If the wireless remote control will not be used for
a long period, take the batteries out to avoid battery
leakage and damage to the wireless remote control.
It should be placed 1m(39 inches) away from the TV
set or stereo sound sets.
Operation should be within its receiving range.
If the remote control does not operate normally, please
take the batteries out, and reinsert them 30 seconds later; if
If the main unit needs to be remote controlled, please
aim the remote controller at the receiver of the main unit in order
to improve the receiving signal to the unit.
When the remote controller sends out signal, a mark
will flicker for about One second. The chime will sound if the main unit
receives effective signal.
it is still not operating ,please replace the batteries.
to the polarity. (As shown in Fig 2.)
4. Attach the back cover of wireless remote control.
Sketch map for
changing batteries
-8-
MS-SVU052A-EN 04/14
