background image

 

 

 

 

 

 

 

 

 

Piping

 

Coil connections

 

To complete piping connections, attach the 
water piping with 3/4-inch MPT connection to 
the coil. The water inlet is on the bottom and 
water outlet on the top of the coil. Coil 
connection size and coil connection locations 
are given on Figure 4,5,6. Water inlet/ 
outlet connections of unit with valve package 
are 3/4-inch MPT. 3/4-inch FPT union 
should be provided by installer. 

 

Condensate Drain Connections

 

Either PVC pipe or steel pipe with 3/4-inch 
FPT connection can be used as a drain line. 
Attach the drain line to the drain connection 
with tape-sealant to prevent leakage. A drain 
line pitch with a minimum slope of 1:50 is 
recommended. 

 

 

 

Installation 

 

 

 

 

Electrical Connections

 

For wiring and Installation, refer to the wiring 
diagram decals on each unit. Also see 
Figure 7 for wiring diagrams. 

 

A grounding point, which must be properly 
connected to the building grounding system, 
has been provided with a mark on the vertical 
side of the inlet collar. 

 

All  electrical  connections  are  to  be  made in 
accordance  with  local  electrical  codes  and 
ordinances. 

 

WARNING: Disconnect electrical power 
source and secure in disconnected 
position before servicing the unit. Failure 
to do so may result in personal injury or 
death from electrical shock.

 

 

 

 

 

 

 

 

 

 

CAUTION: Use only copper conductors 
for wiring connections. Unit terminals are 
not designed to accept other types of 
wiring. Aluminum or other conductors 
may cause overheating and unit damage.

 

 

Notice: The reserved space for power 
supply cords is 20 mm in diameter.

 

 

Notice: Table shows the range of the fan 
coil units with different heater options. 
Please refer to the current and use the 
proper power supply cords.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HFCF-SVX01A-EN

 

 

 

 

 

Summary of Contents for HFCF-SVX01A-EN

















Reviews: