background image

SSC-SVN001H-EN

9

Refrigerant Piping

Units should be interconnected pre-

ferably by copper pipes.

The Table 04 presents connection 

sizes for Onix units and remote 

TRCE/TRAE condensing units, as 

well as liquid and suction piping si-

zes recommended for the intercon-

nection.

The equivalent lengths indicated al-

ready include losses due to valves, 

curves, elbows, reductions, etc.

Maximum Distances 

(Recommended)*

Distance between units: 

46m

Difference between unit levels:

 18m

(*) – Calculated distance, considering equivalent 
length of connection elements.

Contact 

Trane 

for distances above 

the recommended ones.

Refrigeration Piping 

(Interconnection)

Instructions for Fixing the Expan

-

sion Valve Thermostatic Bulb 

- In the suction line, as closest as 

possible to the evaporator outlet.

- Before external equalization, in an 

horizontal line run.

Tab. 04 - Connection and Pipe Sizes Recommended by Circuit.

Note: For equivalent lengths above the values indicated, please contact Trane or an authorized installer.

- The copper tube must be comple-

tely clean.

- At the 12h position for pipes smal-

ler than 7/8”, and 4h or 8h position 

for 7/8” or larger pipes.

- Then insulate the pipes using ther-

mal sheets.

MOUNTING DIAGRAM

DRIER FILTER AND LIQUID SIGHT GLASS

CAUTION:

!

Do not operate the unit without 

air filters.

MOUNTING DIAGRAM

DRIER FILTER

DRIER FILTER - 

Ø1/2”  AND  Ø5/8” THREAD

WELDED DRIER FILTER

Ø5/8” Ø7/8” Ø1.1/8”

Welded filter Ø5/8” 
only for CXPA 25

DRIER FILTER -  

Ø1/2”  AND  5/8” THREAD

LIQUID SIGHT GLASS 

WITH HUMIDITY INDICATOR

WELDED DRIER FILTER

Ø5/8”Ø7/8”Ø1.1/8”

Welded filter Ø5/8” 
only for CXPA 25

Connection Size (in.)

Equivalent Pipe Length

 CXS Mod. 

TRCE/TRAE

<12m

12~18m

18~24m

24~30m

30~36m

36~46m

Line(Ton)

Liq.

Suct.

Liq.

Suct.

Liq. Suct.

Liq.

Suct.

Liq.

Suct.

Liq.

Suct.

Liq.

Suct.

Liq.

Suct.

5

1/2

7/8

1/2

7/8

1/2

7/8

1/2

7/8

1/2

7/8

1/2

1-1/8

5/8

1-1/8

5/8

1-1/8

7,5

5/8

1-1/8

1/2

1-1/8

1/2

7/8

1/2

1-1/8

5/8

1-1/8

5/8

1-1/8

5/8

1-1/8

7/8

1-3/8

10

5/8

1-3/8

5/8

1-3/8

5/8

1-1/8

5/8

1-1/8

5/8

1-1/8

7/8

1-3/8

7/8

1-3/8

7/8

1-3/8

12,5

5/8

1-3/8

5/8

1-3/8

5/8

1-1/8

7/8

1-3/8

5/8

1-5/8

7/8

1-5/8

7/8

1-5/8

7/8

1-5/8

15

5/8

1-5/8

7/8

1-3/8

5/8

1-3/8

7/8

1-3/8

7/8

1-3/8

7/8

1-5/8

7/8

1-5/8

7/8

1-5/8

20

5/8

1-5/8

1 1/8

1-5/8

7/8

1-3/8

7/8

1-5/8

7/8

1-5/8

7/8

1-5/8

7/8

1-5/8

1-1/8

2-1/8

25

7/8

2-1/8

1 1/8

1-5/8

7/8

1-3/8

7/8

1-5/8

7/8

1-5/8

1-1/8

2-1/8

1-1/8

2-1/8

1-1/8

2-1/8

EXPANSION VALVE

EQUALIZATION

SUCTIONPIPE

ORSUCTIONHEADER

THERMAL BULB

INSULATION

BULB

EVAPORATOR

COIL

BULB FIXED AT 12H POSITION

FOR PIPES UP TO DIA. 3/4”

AND 4H POSITION OR 8H POSITION

FOR 7/8”-DIA. PIPES AND LARGER

12H

8H

4H

Summary of Contents for CXPA 050





































Reviews: