manualshive.com logo in svg

Trane CeilAir CW, Installation, Operation And Maintenance Manual, Page: 26 / 52

Share
Download
Trane CeilAir CW Installation, Operation And Maintenance Manual Download Page 26

NOTICE

Transformer Damage!

Connecting additional load to a factory supplied control 
transformer may result in overloading the transformer. 
Do not rewire the unit's individual components.Do not 
connect any additional loads to the system control 
transformers.

Installation

26

 AH-SVX008C-EN

Remote Condenser

For systems equipped with a remote condenser, the 
installer must provide main power wiring to the remote 
condenser control box. A separate equipment ground lug 
is provided within the control box for termination of the 
earth ground wire. Refer to the electrical drawing supplied 
with your system and the wiring diagram supplied with 
the condenser (typically located in the condenser electric 
box).

As an option, control wiring may be installed between the 
A/C system and the condenser for the system controller to 
enable condenser operation only when the compressor is 
running.

You must remove the jumper from the remote condenser 
terminal board (see the condenser wiring diagram). Wire 
24 VAC control conductors from the terminal board within 
the A/C unit to the remote condenser terminal board. If 
control wires aren't installed (and the jumper remains in 
place), the condenser is always enabled and will turn on 
and off based on the condenser's pressure control 
settings.

Remote Condensing Unit

Systems equipped with a remote condensing unit require 
field wiring between the evaporator system and the 
remote condensing unit. The number of conductors 
required varies based upon the options provided. Refer to 
the electrical drawing(s) supplied with your unit to 
determine the exact number of field wires and proper wire 
terminations required specifically for your system.

Glycol-cooled systems equipped with a pump package 
require field wiring between the A/C unit and pump pack- 
age. The installer must wire two control conductors from 
the terminal board within the A/C unit to the pump package 
electric box. Refer to the electrical drawing(s) supplied 
with your unit to determine the exact number of field wires 
and proper wire terminations required specifically for your 
system.

Water/Glycol Systems

Glycol-cooled systems equipped with a pump package 
require field wiring between the A/C unit and pump pack- 
age. The installer must wire two control conductors from 
the terminal board within the A/C unit to the pump pack- 
age electric box. Refer to the electrical drawing(s) supplied 
with your unit to determine the exact number of field wires 
and proper wire terminations required specifically for your 
system.

Remote Shut Down

The unit provides an interface that allows for remote shut 
down. A normally-closed switch rated at 5 amperes at 
24VAC is required for this purpose. Two conductors from 
the normally closed switch must be connected to the 
control terminal board located within the unit electric box. 
Refer to the supplied electrical drawing for the appropriate 
wire terminations.

Note:

All wiring must be provided in accordance with 
National Electrical Code and local code 
requirements for Class 2 circuits.

Optional Equipment

Condensate Pump

Systems supplied with a field installed condensate pump 
require power and control field wiring. The control wires 
from the terminal board in the electric box should be run 
through the overflow switch in the condensate pump 
housing.

After installing the condensate pump, connect two power 
conductors from the condensate pump main power 
terminals to the air conditioning unit and a ground wire to 
the unit ground stud located within the unit electric box. 
Two control conductors must be wired to the control 
terminal board located within the unit electric box. The 
condensate pump is provided with pigtail leads for splice-
type wire connections with twist-on connectors (wire 
caps). Refer to the supplied electrical drawing for proper 
wire terminations.

Humidistat/Dehumidistat

The humidistat/dehumidistat are mounted in the same 
manner but are wired differently. The humidistat/
dehumidistat both require two conductors for connection 
to the air conditioning system. The controls have pigtail 
leads for splice type wire connections with twist on 
connectors (wire caps). Refer to the supplied electrical 
schematic for proper wire terminations.

Remote Water Detector

There are two types of water detector available with TR-
OHS units: Spot type and strip/cable type.

Spot Type

A remote spot type water detector requires three 
conductors to be wired to the control terminal board in the 
unit electric box. The wire insulation must be rated at 600V. 
The water detector has pig-tail leads for splice type wire 
connections with twist on connectors (wire caps). Refer to 
the supplied electrical drawing for proper wire 
terminations.

Strip/Cable Type

A remote strip/cable type water detector is provided with 
a two conductor cable harness with a quick connect fitting 
on the end. The harness mates to the fitting on the water 
detector and connects it to the control board inside the 

Summary of Contents for CeilAir CW





















































Reviews:

No comments