Trane CeilAir CW Installation, Operation And Maintenance Manual Download Page 14 | Manualshive

Page: 14 / 52

Trane CeilAir CW Installation, Operation And Maintenance Manual Download Page 14

Figure 7.

A-Tech controller installation

Installation

14

AH-SVX008C-EN

2. Place the base temporarily over the wire hole opening

in the wall. Level the base and mark the screw locations
through the two provided mounting slots.

NOTICE

Sensor Damage!

Do not touch the temperature sensor on the bottom left
corner of the thermostat. The sensor can be damaged if
handled improperly.

3. If using the supplied anchors, drill two 3/16 in. holes

and tap in the wall anchors. If only the screws are being
used, drill two 3/32 in. holes.

4. Fasten the base to the wall using the supplied screws.

5. Connect wiring between the thermostat and

equipment. See the A-Tech wiring instructions in
Section

“A-Tech 1.1 Programmable Thermostat,” p. 22

and

“A-Tech 1.2 Programmable Thermostat,” p. 22

6. Reinstall thermostat cover to base.

Figure 8.

Spot cooler grille

.75 in/19 mm
THICK
GASKET

Figure 9.

Ducted system typical air patterns

90° / RIGHT ANGLE

IN/OUT

SAME FACE

STRAIGHT-THRU

SUPPLY

AIR OUTLET

«
...
12
13
14
15
16
...
»

Summary of Contents for CeilAir CW





















































Reviews:

No comments