3
March 2012
© 2012 Trane.
X39641168-01B
All rights reserved.
1
2
Setup Instructions
Trane Programmable Thermostat
X13511537-01/BAYSTAT150A/THT02774
SAFETY WARNING
Only qualified personnel should install and service the equipment.The
installation, starting up, and servicing of heating, ventilating, and air-
conditioning equipment can be hazardous and requires specific
knowledge and training. Improperly installed, adjusted or altered
equipment by an unqualified person could result in death or serious
injury. When working on the equipment, observe all precautions in the
literature and on the tags, stickers, and labels that are attached to the
equipment.
More information:
https://www.trane.com/stat
Time Setup
To change the current time:
1. From the
Home
screen, press
,
,
,
,
,
.
2. Press
,
, or
to scroll between hours and minutes.
AM
PM
Hours
Minutes
1. Press
to increase or
to decrease the hour or minute.
PM
PM
AM
PM
Changing Hours
Changing Minutes
1. Press and hold
for 2 seconds or wait 10 seconds to
Save
and
Exit
.
System Mode Setup
To set the system mode:
1. From the operating screen, press
,
. The current mode flashes.
2. Press
or
to select a mode.
Emergency
Heat
Cool
Auto H/C
Off
Heat
OFF
Note:
Not all system choices may be available depending on the
system configuration 0130
.
3. Press and hold
for 2 seconds or wait 10 seconds to
Save
and
Exit
.
Fan Mode
The fan mode is displayed only on systems configured with the fan
enabled.
For systems configured with a fan, the fan setting is shown on the
display. In addition, the setting also appears on the display when
pressing
,
,
from the
Home
screen.
The fan mode setting can be overridden by pressing
or
when the
fan mode flashes. Press and hold
for 2 seconds or wait 10 seconds to
Save
and
Exit
. Refer to the section,
“Timed Override (TOV)”
.
On Mode:
Arrows Flash
Auto Mode:
Auto Flashes
Important:
When this thermostat is configured in
programmable mode (
0140=1)
, then changing the
Fan
Mode
from the
Home
screen puts the thermostat into
Timed Override (TOV)
and is only temporary. The fan
goes back to the schedule setting after the TOV timer
expires.
Timed Override (TOV)
A timed override can be used to temporarily change the heating setpoint,
cooling setpoint, fan mode, and/or occupancy setting from the
programmed schedule.The override can be set for up to 99 days and up
to 23 hours.
To enter a timed override:
1. From the operating screen, press
or
2 times.The thermostat
enters timed override mode with the hourglass
and setpoint
flashing.
2. Press
or press
or
to move from either left or right through
the selections. Some of the selections may not be available
depending on the system type.
Cooling
Setpoint
Occupancy
Setting
Hours
Heating
Setpoint
Fan
Setting
HOURS
(Days)*
DAYS
3. Press
or
to change the value of the currently active
(flashing)
selections. Repeat steps 2 and 3 for the desired settings.
Note:
To reach the DAYS setting, the user must press
from the
hours setting
.
4. Press and hold
for 2 seconds or wait 10 seconds to
Save
and
Exit
.
Note:
The thermostat will return to the scheduled operation when:
• the override time expires, or
• pressing and holding
an
for 2 seconds.
Important:
When in timed override mode, if the system
selection is changed (EmHeat, Heat, Cool, Auto, OFF), this
change will take the thermostat out of TOV mode.
Important:
Whenever the thermostat is in TOV mode, a
solid hour glass ( ) indicator displays at the bottom of the
screen.
