background image

Page 11

INSTALLER'S GUIDE

STEP 

11

 -

 Replace Heater compartment panel on air 

handler.

Section 6. Tables

Important: 

The BAYEV* electric heat accessory may include up to a combination of three 60 amp circuit breakers to 

provide an electrical disconnect for service personnel that is intended to help protect internal electrical components in 

the event of a short circuit or ground fault. As designed, the circuit breakers supplied in the BAYEV* accessory

 DO NOT

 

provide overcurrent protection of the branch circuit. Therefore, the branch circuit(s) shall be sized and protected according 

to the unit nameplate.

Table 6.1 BAYEV -- HEATER DATA

Heater Model No.

Number of 

Circuits

240 VOLT

208 VOLT

Capacity

Heater Amps 

per Circuit

Capacity

Heater Amps 

per Circuit

kW

BTUH

kW

BTUH

BAYEVCC25BK1

3

24.00

82000

40/40/20

18.00

61500

34.6/34.6/17.3

Table 6.2 MINIMUM HEATER AIRFLOW CFM - HEATER MATRIX

MODEL NO.

BAYECC25BK1

W/O HP / WITH HP

TAM7A0C48H41S

1625 -- 1813

TAM7B0C60H51S

1625 

 

-- 1813

--

TAMGA0C48H41S

1625 -- 1813

TAMGA0C60H51S

1625 

 

-- 1813

TAM8A0C48V41C

1625 -- 1813

TAM8B0C60V51C

1625 

 

-- 1813

SEE AIR HANDLER NAMEPLATE OR PRODUCT DATA FOR EXCEPTIONS

  Not approved for 208V when installed in horizontal left position without Heat Pump.

          

Summary of Contents for BAYEVCC25BK1













Reviews: