background image

26

 WSHP-SVX02E-EN

Maintenance

Preventive Maintenance

Maintenance on the unit is simplified with the following 
preventive suggestions:

WARNING

Hazardous Voltage!

Failure to disconnect power before servicing could 
result in death or serious injury.

Disconnect all electric power, including remote 
disconnects before servicing. Follow proper lockout/
tagout procedures to ensure the power can not be 
inadvertently energized. Verify that no power is 
present with a voltmeter.

A strainer (60 mesh or greater) must be used on an open 
loop system to keep debris from entering the unit heat 
exchanger and to ensure a clean system.

For units on well water, it is important to check the 
cleanliness of the water-to-refrigerant heat exchanger. 
Should it become contaminated with dirt and scaling as a 
result of bad water, the heat exchanger will have to be back 
flushed and cleaned with a chemical that will remove the 
scale. This service should be performed by an experienced 
service person.

WARNING

Hazardous Chemicals!

Failure to follow this safety precaution could result in 
death or serious injury. Coil cleaning agents can be 
either acidic or highly alkaline and can burn severely if 
contact with skin or eyes occurs. 

Handle chemical carefully and avoid contact with skin. 
ALWAYS wear Personal Protective Equipment (PPE) 
including goggles or face shield, chemical resistant 
gloves, boots, apron or suit as required. For personal 
safety refer to the cleaning agent manufacturer’s 
Materials Safety Data Sheet and follow all 
recommended safe handling practices. 

It should be noted that the water quality should be checked 
periodically. Refer to the table below.

Table 14. Water quality table

Scaling

Calcium and magnesium (total hardness) Less than 350 ppm

Corrosion

pH
Hydrogen Sulfide
Sulfates
Chlorides
Carbon Dioxide
Total dissolved solids (TDS)

7-9.5
Less than 1 ppm
Less than 25 ppm
Less than 125 ppm
Less than 75 ppm
Less than 1000 ppm

Biological Growth

Iron Bacteria

Low

Erosion

Suspended Solids

Low

Summary of Contents for Axiom EXW 060 Series

































Reviews: