background image

Note: 

When connecting the power supply cord, make sure that the phase of the power supply 

matches with the voltage and phase indicated on the nameplate, .  If the power supply does 
not match the nameplate, the compressor will not operate properly and the equipment may be 
damaged.

Grounding Requirements

• 

Follow your local, State and National Electric Codes (NEC) when grounding this unit.

• 

The air conditioner is classified as a Class I appliance and must be grounded.

• 

The yellow-green wire of the air conditioner is the ground wire and cannot be used for other 
purposes or cut off, otherwise it would create an electric shock hazard.  

• 

Do not ground the unit to a utility pipe, arrester or telephone ground.  Incomplete ground may 
cause electrical shock or fire. A high current surge from lightning or other sources may cause 
damage to the air conditioner.  

Installation of Controllers

Refer to the controller installation manual for instructions and functionality.

Wiring Precautions

23

Floor and Ceiling Unit

 

CAUTION

Improper operation may lead to personal injury or property damage. 

Summary of Contents for 4MXX8509B10N0
































Reviews: