Trane Technologies BAYSTAT152A, Installation, Operation And Maintenance Manual

Page: 25 / 56

BAS-SVX44C-EN 25
Configuration Option Setup
Installation Options
Table 7. Installer configuration setup menu
Opt.
No.
Name Def Values/Descriptions Notes
0100 Temperature indication/
Resolution 0
• 0= °F, 1 degree resolution
• 1= °F, 0.5 degree resolution
• 2= °C, 1 degree resolution • 3= °C with 0.5 degree
resolution
• 4= °C with 0.1 degree
resolution
This setting affects indoor temperature display and setpoint
display resolutions. Outdoor temperature display area is
always ±1 resolution for both F and C. Refer to Option 0210.
0110 Clock Format 12
• 12= 12-hour clock • 24= 24-hour clock
0120 Year 11
• 11–99
Available year range: 2011–2099. This value is updated to the
real time clock after setting. Day of the week is updated
0121 Month 1
• 1–12
This value is updated to the real time clock after setting. Day
of the week is updated automatically.
0122 Day 1
• 1–31
Month dependent: this value is updated to the real time clock
after setting. Day of the week is updated automatically.
0125 Daylight Savings 2
• 0= Disabled
• 1= US (1987), changeover at
2:00am
• 2= US (2007), changeover at
2:00am
• 3= Europe, changeover at
1:00am
• 4= Manual, changeover at
2:00am
0126
0127
0128
0129
• Spring Ahead Month
• Spring Ahead Day
• Fall Back Month
• Fall Back Day • 03
• 01
• 11
• 01 • 01-12
• 01-31
• 01-12
• 01-31
Options available only if 0125 is set to 4.
0130 System Selection 8
• 1= 1H/1C (Conv) 1st Stage
Heat (W), 1st Stage Comp (Y),
Fan (G)
• 2= 1H/1C (HP) 1st Stage Comp
(Y), Changeover (O/B), Fan (G)
• 3= 1H (Conv) 1st Stage Heat
(W), without fan
• 4= 1H (Conv) 1st Stage Heat
(W), Fan (G)
• 5= 1C (Conv) 1st Stage Comp
(Y), Fan (G)
• 6= 2H/1C (HP) 1st Stage Comp
(Y), Changeover (O/B),
Auxiliary Heat (W1), Fan (G)
• 7= 2H/2C (Conv) 1st & 2nd
Stage Heat (W,W2), 1st & 2nd
Stage Comp (Y,Y2), Fan (G)
• 8= 2H/1C (Conv) 1st & 2nd
Stage Heat (W,W2), 1st Stage
Comp (Y), Fan (G)
• 9= 1H/2C (Conv) 1st Stage
Heat (W), 1st & 2nd Stage Comp
(Y,Y2), Fan (G)
• 10= 2H/2C (HP) 1st & 2nd
Stage Comp (Y,Y2), Changeover
(O/B), Fan (G)
• 11= 3H/2C (HP) 1st & 2nd
Stage Comp (Y,Y2), Changeover
(O/B), Auxiliary Heat (W1), Fan
(G)
0140 Schedule Options 1 0=Non-programmable 1= Programmable
0150 TOD/Economizer Output
(Terminal A) 0
• 0= Unused
• 1= TOD energizes terminal
A
during occupied period, not
during unoccupied period.
• 2= Economizer energizes
terminal A during a call for cool.
TOD is not available in Non-programmable Mode. (Refer to
Option 0140)
0151
Heat Fan Operation 0 0= System controls fan 1= Thermostat controls fan
Only shown for conventional system with heat stages and fan
capability. For heat pump, the fan relay operates with
thermostat control.
0153 Reversing Value O/B 0 0= O/B ON when call for cool 1= O/B ON when call for heat
Only shown for heat pump systems.
0160 Cycles Per Hour (CPH) [First
Stage Compressor] 3 1–5
Only for systems with cool or HP stage. (Refer to Option 0130.)
Selection in this stage changes 2nd stage cool default CPH.
0161 CPH (Second Stage
Compressor) 3 1–5
Only for systems with 2-cool or HP stages. (Refer to Option
0130.)
0162 CPH (First Stage
Conventional Heat) 5 1–10
Only for conventional systems with heat stages. (Refer to
Option 0130.) Selection in this stage changes default CPH of
2nd stage heat.
0163
CPH (Second Stage
Conventional Heat) 9 1–10
Only for conventional systems with two stages of conventional
heat.
0164
CPH for Auxiliary Heat 9 1–10
Only shown for 2H/1C HP or 3H/2C HP systems. (Refer to
Option 0130.)
0165
CPH for Emergency Heat 9 1–10
Only shown for 2H/1C HP or 3H/2C HP systems. (Refer to
Option 0130.)
0170 Continuous Backlight 0 0= Backlight ON time is limited 1= Backlight ON continuously