background image

IN

STALL TIM

E

PARTS LIST OF COMPONENTS

Tri-Fold Tonneau Cover

Fits:

Ratchet & 1/2” Socket

THE TRAILFX TRI-FOLD TONNEAU COMES FULLY ASSEMBLED.

30-60 min

Cutting Not Required

Drilling Not Required

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.

[email protected]

1 866 638 4870

LIMITED LIFETIME WARRANTY

READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.

DO NOT OVER TORQUE. A TORQUE WRENCH IS NOT NECESSARY.

IF PREFERRED, TORQUE IS APX 75 INCH LBS.

www.TrailFX.com

Tools Required

Qty

Part Description

Qty

Part Description

Components

Rev 041015

Page 1 of 7

TFX2521 - Ram 6.5’ 2002-2017

KS-N2

1

2

3

4

5

6

7

Hard Folding Cover

Driver (Left) Mounting Rail

Passenger (Right) Mounting Rail

Drain Tubes (x2)

Clamps (x6)

Star Knobs (x4)

Lock Washers (x4)

8

9

10

11

Flat Washers (x4)

Front Mounting Retainer (x4)

Front Mounting Bolts (x4)

Rubber Filler Strips (x6)

5(9,6,216

5(9

'(6&5,37,21

'$7(

$

1(:3$57

$

%

&

'

&$'*(1(5$7(''5$:,1*
'21270$18$//<83'$7(

6&$/(

6,=(

&$'),/(

3$5712

$

6+((7

2)

5(9

'$7(

$33529$/6

'5$:1

&+(&.('

81/(6627+(5:,6(63(&,),('

',0(16,216$5(,1,1&+(6

72/(5$1&(6$5(

'(&,0$/6$1*/(6

;;

;;;
0$7(5,$/

),1,6+

7+(,1)250$7,21&217$,1(',17+,6'5$:,1*

,67+(62/(3523(57<2)81'(5&29(5$1<

5(352'8&7,21,13$5725:+2/(:,7+2877+(

:5,77(13(50,66,212)81'(5&29(5,6

352+,%,7('

$

%

&

'

-*4

8VHU/LEUDU\6RFNHW:UHQFKDQG6RFNHWV

,GHDOIRUYDOLGDWLQJWKHDELOLW\WRWLJKWHQIL[LQJV

 

Summary of Contents for Tonneau








Reviews: