background image

Söllnerstr. 9 92637 Weiden

[email protected]

+49 (0)961 48 23 0 0

S7-USB user manual

48 / 85

2019/10/05 05:07

The username is maximal 8 characters long. Every user and the administrator should use a password
which is used to login in the TELEService over a telephone-line.

After three failed retries the connection is hanged up, so you must call again (not like the original TS-
adapter).

After changing the password for a user/administrator you must re-type it again correctly.

You can enter a callback number which is used for a callback from the TS-adapter. After you dialed the
number of the TS-adapter, you are asked for username and password. In case the username and password
is valid, the connection is hang up and the TS-adapter calls back the configured callback number.

7.5.5 Index "GSM/ISDN/SMS":

Information about the three different devices:

Analog Modem:

Type You could choose the location of the modem.

ISDN Modem:

Type Choose the type of the ISDN network:
AT&T 5ESS Nothern Telecom DMS-100 EuroISDN NET3 (Standard) INS64 US NI-1 VN4 Protocol Choose the
transfer protocol type:
Modem like V.120 X.75 (Standard) ML-PPP SoftBonding HDLC CLEAR MSN Multiple Subscriber Number is
used for all ISDN channels. If empty no MSN is used.

GSM Modem:

Summary of Contents for S7-USB






















































































Reviews: