background image

4

A332T1.en.fm

5

CHART OF TYPES A332

6

OPERATION

Feeding the strapping around the
package

The strapping is fed around the package in the
direction as shown in the illustration. The strapping
end is held tightly with the left hand and pulled firmly
towards the operator with the right hand.

Loading the strapping

The rocker is raised with the right hand. The left hand
inserts the two straps lying precisely upon another
into the tool until they hit the strap stops.
The lower strap end must slightly protrude the end of
the base plate.
Be certain that the strapping is held by the strap guide.

Item No.

Model

Strap width

Strap thickness

13.2250

A332/9.5/0.38-0.50

9.5mm / 3/8"

0.38 - 0.50 mm / 0.015 - 0.020"

13.2260

A332/10/0.38-0.50

10.0mm

0.38 - 0.50 mm / 0.015 - 0.020"

13.2270

A332/12.7/0.38-0.50

12.7mm / 1/2"

0.38 - 0.50 mm / 0.015 - 0.020"

13.2280

A332/13/0.38-0.50

13.0 mm

0.38 - 0.50 mm / 0.015 - 0.020"

When handling strap, always wear protective
gloves and safety glasses with side shields
which conform to ANSI Standard Z87.1.

WWW.TRADITIONALTOOL.COM

For Parts & Service 1-877-862-6699

Summary of Contents for 13.2250













Reviews: