background image

-- Wide Dual Band Booster (Model: PODRP27)

      

  

  

9

User  Manual

 

You may need longer cables, more than 2 coverage antennas or other items in 

order to fully cover your building. We can make (almost) any cable length and 

can help design a system that fits your application.   

5.4  Isolation and Separation 

Isolation refers to the proper distance or separation needed to keep the Donor 

antenna signal pattern and the Coverage antenna signal pattern away from 

each other.   

Isolation becomes particularly problematic when Omni-directional antennas 

are used for both the Donor and the Coverage antennas. Since these 

antennas transmit in a circle (or more accurately a sphere) it is very easy for 

these spheres to overlap and thus negate the repeater system.   

6  Production Operation 

6.1  Notices 

Follow below safety items carefully before installation, implementation, 

maintenance and operation for this product 

)

 

Repeater amplifies BTS uplink and downlink signal, it can extend BTS 

coverage area in downlink, but also effect BTS receive sensitivities in 

uplink.  

)

 

BS and MS port must be connected to donor antenna and service antenna 

when powers supply on; otherwise the equipment will be damage for long 

term use. 

)

 

When use repeater for outdoor, the distance between donor antenna and 

service antenna must be >20metes, otherwise the repeater will be damage 

because isolation problem for long term use. 

)

 

Donor antenna need to be lighting proof and lighting rod need to be install 

for donor antenna installation pole outside 

)

 

Check input power, require input power less than maximum input power of 

repeater, otherwise the repeater cannot work well. 

)

 

Keep clear for label and indicator on surface of repeater to be identified. 

www.amplificadorcelular.com   PBX (1) 231 9661 Cel 310 309 9002

Summary of Contents for PODRP27












Reviews: