manualshive.com logo in svg

TR-Electronic MP-200, User Manual, Page: 134 / 153

Share
Download
TR-Electronic MP-200 User Manual Download Page 134

Projecting with TwinCAT System Manager V2.10 

 

 TR-Electronic GmbH 2016, All Rights Reserved 

Printed in the Federal Republic of Germany 

Page 134 of 153 

TR-EMO-BA-GB-0022 v03 

09/29/2020 

 
Now the drive can be turned on: 
 
"Opmode" 0x6060 = 0x0001 

-> "OpmodeDisplay" 0x6061 = 0x0001 

 
"Control word" 0x6040 = 0x0000 

-> "Status word" 0x6041 = 0x0640 // switch-on disabled 

 
"Control word" 0x6040 = 0x0006 

-> "Status word" 0x6041 = 0x0621 // ready to switch on 

 
"Control word" 0x6040 = 0x0007         // this step can be skipped 

-> "Status word" 0x6041 = 0x0623 // switched on 

 
"Control word" 0x6040 = 0x000F 

-> "Status word" 0x6041 = 0x0637 // operation enabled 

 
The drive should be turned on now. If it was rotating, it tries to stop. 
 
Travelling  to  the  "Target  position"  0x607A  is  triggered  by  a  rising  edge  (0->1)  in 
STW.4 "New set-point": 
 
"Control word" 0x6040 = 0x001F 

-> "Status word" 0x6041 = 0x1237 

 
The  drive  travels  to  the  location,  that  has  been  indicated  by  the  "Target  position" 
0x607A, unless it is already travelling to another destination. 
 
If the target position is reached 

-> "Status word" 0x6041 = 0x1637 

 
"Control word" 0x6040 = 0x000F 

-> "Status word" 0x6041 = 0x637 

 
"Control word" 0x6040 = 0x003F 

-> "Status word" 0x6041 = 0x1237 

 
The  drive  immediately  travels  to  the  location,  that  has  been  indicated  by  the  "Target 
position" 0x607A. If it is already travelling to another destination, it aborts that journey. 
 
If the software  position limits 0x607D are not tighter than  the position range 0x607B, 
the  drive  always  travels  the  shortest  way,  that  may  cross  the  start  and  end  values. 
Then it will never travel further than half of the user stroke. 
Otherwise it must avoid the start and end values, so that the travelled distance may be 
up to the full user stroke - 2. 
 
If  the  destination  is  outside  the  range  or  position  limits,  the  drive  travels  as  far  as 
possible, but it sets the status bit 11 "Internal limits active" in the status word 0x6041. 
If the torque reaches the torque limit, the drive also  sets the status bit "Internal limits 
active". 
 

Summary of Contents for MP-200


























































































































































Reviews:

No comments