manualshive.com logo in svg

TPS WP-81, Manual, Page: 16 / 51

Share
Download
TPS WP-81 Manual Download Page 16

 

Page 16 

5.   pH Calibration 

5.1  Calibration Procedure 

1.  Plug  the  pH  sensor  into  the 

pH

  socket.  Temperature  measurements 

are made via the Conductivity sensor, so this needs to be connected 
for Automatic Temperature Compensation. 

2.  Switch the meter on. 

3.  Ensure  that  temperature  has  been  calibrated  or  manually  set  (see 

sections 7.1 & 7.4). If the decimal point in the temperature reading is 
shown by a “

“, then the temperature value is not calibrated. 

4.  Remove  the  wetting  cap  from  the  pH  sensor.  Rinse  the  pH  and 

Conductivity sensors in distilled water and blot them dry. 

5.  Ensure  that  you  are  using  buffers  which  have  been  selected  for 

automatic  buffer  recognition.  See  section  17  for  a  detailed 
explanation. 

6.  Place both sensors into a small sample of pH7.00 (or pH6.86) buffer, 

so  that  the  bulb  and  reference  junction  are  both  covered,  as  per  the 
diagram  below. 

DO  NOT

  place  the  sensors  directly  into  the  buffer 

bottle. 

 

Summary of Contents for WP-81




















































Reviews:

No comments