background image

B.  SAFETY CONSIDERATIONS

WARNING:  Please follow manufacturers test 
procedures whenever possible.  Do not place the
sensor cage located on the end of the gooseneck on

hot or in hot locations.

GENERAL GUIDELINES

ALWAYS

Turn your detector on in a “clean air” environment away
from the test location.

Inspect the sensor cage to ensure it is securely attached.

NEVER

Place the detector or sensor cage in or on a hot item.

4

5

C. TECHNICAL DATA

1. Features and Benefits

Auto Zero

Automatically sets the sensor to 

zero at start up.

%LEL

Displays the percentage lower explosive
limit (LEL)

PPM

Displays the amount of leakage in
parts per million (ppm)

Mute

Mutes the speaker and earphone alarm

Zero

Manually sets the sensor to zero

Adjustable

Alarm point can be set as required

Alarm

Visual

Alarm LED’s located on the front and

Alarm

in the sensor cage tip

Auto Off

When enabled, the 721 turns off after
approximately 20 minutes to saves battery
life. Can be disabled

.

2. Product Applications

Perform the following tests and/or measurements with the 721
leak detector:

• Locate combustible gas leaks in joints and fittings.
• Determine Lower Explosive Limit percentage.
• Determine the combustible gas leak level in ppm   (parts per
million).

721 manual_082208.qxd  11/11/2008  7:09 AM  Page 4

Summary of Contents for 721

















Reviews: