TPI 709 Manual Download Page 5

Page: 5 / 46

Instrument Overview

Front View

Rubber Boot

Protects the instrument from accidental damage

Display

Large 3 Parameter Backlit LCD Display

Battery Condition Icon

Shows condition of batteries.

Keypad

Selects all available functions

Selected Fuel Type

N GAS, LPG, LIGHT OIL, HEAVY OIL, OPT 1
(Bituminous Coal), OPT 2 (Anthracite Coal),
OPT 3 (Coke), OPT 4 (Butane), OPT 5 (Wood),
OPT 6 (Bagasse)

General Overview (Continued)

Never over saturate your sensors by performing tests on equipment
with gas levels beyond the capability of you analyzer.

Always keep the A794 water trap / filter assembly clean and replace the
filter as necessary. Replacement filter part number is A794F.

This manual will guide you through the functions of the TPI 709 which
will give you many years of reliable service.

Your TPI 709 Flue Gas Analyzer comes complete with the following
standard accessories:

•

TPI 709 Instrument

•

Rubber Boot (A765)

•

Soft Carrying Case (A768)

•

Flue Sampling Probe (A770)

•

In-Line Filter assembly installed on Flue probe (A794)

•

Temperature Probe (GK11M)

•

Mini Pump Protection Filter Assembly and spare filters (A763)

•

Exhaust Spigot (removable) (A764)

•

Instruction Manual

( ) Denotes part number

Your TPI 709 Flue Gas Analyzer has the following options available:

•

Infrared printer (A740)

•

Spare In-Line Filter (A794F is a package of 5 filters)

Rubber
Boot

LCD
Display

Keypad

Battery
Condition
Icon

Selected
Fuel Type

NOTE: When selecting oil as fuel be sure to use the optional

oil filter (A773) or readings could become erratic. See
Appendix E for installation instructions.

lit

Summary of Contents for 709















































Search results

Summary of Contents for 709

Reviews:

Related manuals for 709

Brands by name

Popular brands

TPI 709, Manual

Search results

Summary of Contents for 709

Reviews:

Related manuals for 709

Brands by name

Popular brands