Position two converters back to back between the following end
devices.
Installation Procedure
1. Converter to 10/100Base-TX Device (hub or switch)
Connection
Make sure that the length of twisted pair cable (Category-5)
between 10/100Base-TX device and converter is no longer
than 100 meters.
Connect one end of twisted pair cable to RJ45 jack on the
converter and the other end of the cable to the RJ45 jack on
the 10/100Base-TX device.
2. Converter to Converter or 100Base-FX Device Connection
Connect one (SC) end of a fiber cable to the SC connector on
the converter and the other end of the cable to the SC
!
!
5
2
1
3
4
6
7
TR-965DA
TR-965DB
User's Guide
71030498
Rev 1.0
10/100Mbps Fast Ethernet Converter
Table of Contents
Introduction...............................................................................2
Features....................................................................................2
Network Cable Supported..........................................................3
Package Contents.....................................................................3
Appearance Indication...............................................................4
Installation Guide......................................................................5
Appendix Specifications...........................................................7
Introduction
The TR-965DA/TR-965DB are 10/100Mbps Fast Ethernet
converter. The converter mediates between a 10/100Base-TX
segment and a 100Base-FX segment.It is primarily designed for
large, more high speed/bandwidth demanding workgroups that
require expansion of the Fast Ethernet network.
Features
Complies with IEEE802.3u 10Base-T, 100Base-TX and
100Base-FX standard.
Provide one SC fiber connector and one UTP connector.
The SC fiber connector can transfer and receive data on
one single-mode fiber.
Provide switch configuration of half/full duplex transfer
mode for FX port.
Extend fiber distance up to 20-60km for single-mode fiber.
!
!
!
!
!
AC power connector
RJ45 connetor
SC fiber connetor
!
!
!
Easy-to-view LED indicators provide status to monitor
network activity easily.
External power adapter supply.
Network Cable Supported
The connectors and network cables supported by the converter
are listed in the following:
UTP: Cat 5 Twisted-Pair
Fiber SC: 1300nm 62.5/125 Single-mode Fiber
Package Contents
Before start using the products, make sure that what you have is
what you ordered.
The Converter includes:
One Converter
TR-965DA-20 RJ45--SC 20km Single-mode Fiber,Cat-5
TR-965DA-40 RJ45--SC 40km Single-mode Fiber,Cat-5
TR-965DA-60 RJ45--SC 60km Single-mode Fiber,Cat-5
TR-965DB-20 RJ45--SC 20km Single-mode Fiber,Cat-5
TR-965DB-40 RJ45--SC 40km Single-mode Fiber,Cat-5
TR-965DB-60 RJ45--SC 60km Single-mode Fiber,Cat-5
Type Connetor Transmission Distance Transmission Media
!
!
!
!
!
!
!
One AC adapter
This User's Guide
Appearance Indication
LED Indicators
This converter has LED indicators which can provide a real-time
report. When you take a look at these indicators, you will know
what's happening on your network.
Power(green)
Lights when the adapter is properly plugged
in.
TX_SPD(green)
Lights when the UTP ports is connected to
100Base-Tx device.
TX_LINK/ACT(green)
Steady green indicates that a valid
link exists. Flashing green indicates that the converter is
receiving data or transmitting data from the RJ45 connector.
FX_LINK/ACT(green)
Steady green indicates that a valid
link exists. Flashing green indicates that the converter is
receiving data or transmitting data from the Fiber Optic
connector.
FX_FDX/COL(green)
Steady green indicates that the fiber
optic connector is operating in full-duplex mode. The light is
off Which means that the fiber optic connector is operating in
half-duplex mode. Flashing green indicates for collision.
FDX/HDX Switch
FDX:
The UTP port operate in full-duplex mode ;
HDX:
The UTP port operate in haf-duplex mode;
Notice: You must reset the converter when you achieve the
configuration.
Installation Guide
SC fiber connector works at 1550nm on transferring
data and at 1310nm on receiving data in one single-mode
fiber.
SC fiber connector, inversely, works at 1310nm
on transferring data and at 1550nm on receiving data in a fiber. So
the
Configuration
In order to achieve the aim of effectively expanding a Fast
Ethernet network, You can use the converter for the example :
!
!
TR-965DA's
TR-965DB's
TR-965DA and the TR-965DB must use as partnership
together.
10/100Base-TX
interface
10/100Base-TX
interface
100Base-FX
interface
Twisted-pair
Twisted-pair
Single fiber
Device A
Device B
TR-965DA
TR-965DB
connector on the other converter or 100Base-FX device.
3. Turn on the power
Appendix Specifications
Standard:
IEEE 802.3/IEEE 802.3u
Connector:
1 SC fiber optic; 1 RJ45 jack
Max. Distance:
Twisted Pair(Cat5):100m
Single-mode Fiber Optic: 20km
Power:
external power adapter supply, AC 9V~ 0.8A
O
O
O
O
Temperature:
Operation: 0 C~40 C (32 F~104 F)
O
O
O
O
Storage: -40 C~70 C (-40 F~158 F)
Humidity:
10%-90% (non-condensing)
Dimensions(
LxWxH
):
4.84x2.64x0.94 in.(123mmx67mmx24 mm)
FDX
HDX
9V~
0.8A
50Hz
UTP
