manualshive.com logo in svg

TP-Link TL-WR802N, User Manual, Page: 103 / 186

Share
Download
TP-Link TL-WR802N User Manual Download Page 103

99

Chapter 5

 

Configure the Router in WISP Mode (Hotspot Mode)

Done!

Now only the specific host(s) can visit the target(s) within the scheduled time period.

Note:

When 

LAN Host

 and 

Target

 are both set to be the MAC Address mode, you need to set 

Protocol

: ALL, TCP, 

UDP, ICMP. The default setting is 

ALL

 and it is recommended to keep the default setting.

5. 11.  Advanced Routing

Static Routing is a form of routing that is configured manually by a network administrator 
or a user by adding entries into a routing table. The manually-configured routing 
information guides the router in forwarding data packets to the specific destination.

5. 11. 1.  Static Route List

1. Visit 

http://tplinkwifi.net

, and log in with the username and password you set for the 

router.

2. Go to 

Advanced Routing

 > 

Static Route List

.

•  To add static routing entries:

1.  Click 

Add New

.

2. Enter the following information

.

• 

Destination IP Address 

- The Destination Network is the address of the network 

or host that you want to assign to a static route.

Downloaded from 

ManualsNet.com

 search engine

Summary of Contents for TL-WR802N



























































































































































































Reviews:

No comments