manualshive.com logo in svg

Toyota Lexus IS300, Manual

Share
Download
Toyota Lexus IS300 Manual Download Page 96

EXTERIOR EQUIPMENT

83

SS15021

In case of unlocking the support rod, lift up the hood a
little, move the support rod and unlock it as shown by the
arrow marks in the illustration.

Before closing the hood, check to see that you have not
forgotten any tools, rags, etc. and return the support rod to its
clips–this prevents rattles.  Then lower the hood and make
sure it locks into place.  If necessary, press down gently on the
front edge to lock it.

CAUTION

Before driving, be sure that the hood is securely locked.
Otherwise, the hood may open unexpectedly while
driving and an accident may occur.

TRUNK LID

SS15005c

To unlock the trunk lid, insert the master key and turn it
clockwise.

To close the trunk lid, lower it and press down on it.  After
closing the trunk lid, try pulling it up to make sure it is securely
closed.

The trunk lid can be unlocked using the wireless remote control
key.  For details, see page 16.

If you unlock the trunk lid while the theft deterrent system is in
set, the theft deterrent system will be cancelled.  (For details,
see page 176.)

2003 IS300 from Aug. ’02 Prod. (OM53439U)

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands